Abstract:Nb3Sn conductors are important candidates for high-field magnets for particle accelerators, and they continue to be widely used for many laboratory and NMR magnets. However, the critical current density, Jc, of present Nb3Sn conductors declines swiftly above 12-15T. State-of-the-art Ta- and Ti-doped strands exhibit upper critical field, Hc2, values of 24-26.5T (4.2K) and do not reach the FCC target Jc, which serves as the present stretch target for Nb3Sn development. As recently demonstrated, to meet this goal requires enhanced vortex pinning but an independent and supplementary approach is to significantly enhance Hc2. In this study, we have arc-melted multiple Nb alloys with added Hf, Zr, Ta and Ti and drawn them successfully into monofilament wires to investigate the possibilities of Hc2 enhancement through alloying. Hc2(T) was measured for all samples in fields up to 16T and some up to 31T. We have found that all alloys show good agreement with the standard Werthamer, Helfand, and Hohenberg (WHH) fitting procedure without the need to adjust the paramagnetic limitation parameter (alpha) and spin-orbit scattering parameter (lambda_so). The evaluation of dHc2/dT near Tc, which is proportional to the electronic specific heat coefficient (gamma) and the normal state resistivity (rho_n), allows a better understanding of the induced disorder introduced by alloying in the A15 phase. So far, we have observed that Hf alloying of pure Nb can enhance Hc2(0) by 3-4T to 28T, while adding just 1 at. %Hf or Zr into a Nb4Ta base alloy can raise Hc2(0) to 31T. Very importantly we find that Hf and Zr raise the alloy recrystallization temperature above the usual A15 reaction temperature range of 650°C-750°C, thus ensuring denser A15 phase nucleation in the Nb alloy grain boundaries, possibly leading to a more homogeneous A15 phase Sn content and refined A15 grain size. The potential for...

Effect of Cu doping on properties of RHQT processed powder in tube Nb3Al wires

Superconducting property improvement of RHQT Nb3Al wires through doping of Ti

Improved critical current density of Cu-doped Nb3Al wire through optimized Rapid-Heating Quenching and Transformation method

Microstructure identification of powder in tube Nb3Al wires during rapid heating process and properties of the transformed superconductors

Reproducible stable critical current density in powder-in-tube (PIT) Nb 3 Al superconductors by multi-time rapid heating and quenching process

Preparation of Nb 3 Al Superconductor by Powder Metallurgy and Effect of Mechanical Alloying on the Phase Formation

Introducing nano-scale MgO particles into RHQT Nb 3 Al superconducting wires to significantly improve the critical current density

Formation and upper critical fields of the two distinct A15 phases in the subelements of Powder-In-Tube Nb3Sn wires

The Reaction Process of NbAl Interface in Rod-in-Tube Strands

Preparation of Nb3al by High-Energy Ball Milling and Superconductivity

Phase formation and enhanced performance of Nb3Al prepared by spark plasma sintering and subsequent annealing

Improving phase transformation and superconducting performance of Bi-2223 tapes via Cu addition

Fabrication and Superconducting Properties of MgB2 Wires with Amorphous Carbon Doping by In-situ Powder-in-tube Method

Enhanced flux pinning in (Bi,Pb)-2223/Ag tapes by slight Ni doping

Improvement of Coercivity and Thermal Stability of Anisotropic Nd13fe79.4b7nb0.3ga0.3 Powders by Diffusion of Pr-Cu Alloys

Tuning effect of Cu doping on martensitic transformation and magnetic and mechanical properties of Heusler alloy Mn50Ni40In10−xCux (x = 0–10) ribbons

Effect of Al–Cu–Fe addition on the structure and magnetic properties of Nd-Fe-Co-B ribbons

The doping effect of multiwall carbon nanotube on MgB2/Fe superconductor wire

Influence of Nb Alloying on Nb Recrystallization and the Upper Critical Field of Nb3Sn

Superconducting properties of the powder-in-tube Cu-Mg-B and Ag-Mg-B wires

Enhanced strength-ductility synergy in CuSn alloy via tuning Ti content