Abstract:In this work, the effect of Co addition on the solidification velocity, hardness and refined structure trans-formation of the undercooled Ni-Cu-Co alloys have been systematically investigated. The results show that the grain refinement of Ni-Cu-Co ternary alloys at low undercooling is caused by the intense dendrite remelting. However, the grain refinement at high undercooling is attributed to recrystallization, and the driving force of recrystallization comes from the stresses and plastic strains accumulated by the interaction between liquid flow induced by rapid solidification and primary dendrites. The Co addition can significantly increase the solidification velocity and recalescence effect of Ni-Cu-Co alloys by increasing the number of solidified crystal nucleus and solute diffusion velocity. Under the same undercooling level, the increase of solidification velocity and recalescence effect have strengthened the remelting effect and stress accumu-lation, which can enlarge the critical range for grain refinement gradually. Meanwhile, due to the significant improvement of solidification velocity and stress-induced deformation effect by Co addition, the low angle GBs in the refined structure of Ni-Cu-Co alloys increase and the grain size decreases significantly, which have significantly improved the average hardness of the refined structure. When Co addition reaches 6 %, the refined structures can appear in almost the whole undercooling range and the hardness are improved by more than 100 % compared with the as-cast structure.(c) 2022 Elsevier B.V. All rights reserved.

Simultaneously Enhanced Hardness and Electrical Conductivity in a Cu-Co-Si Alloy by Optimizing Solid Solution Treatment

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Excellent Mechanical Properties and High Electrical Conductivity of Cu-Co-Si-Ti Alloy Due to Multiple Strengthening

Effect of Co addition on hardness and electrical conductivity of Cu–Si alloys

Combined experimental and computational investigation of precipitation behaviour and mechanical properties in a novel Cu–Ni–Si–Co alloy: effect of solution treatment temperature

Simultaneously enhanced hardness and electrical conductivity in a Cu–Ni–Si alloy by addition of Cobalt

Effects of Co/Si Atomic Ratio on Hardness and Electrical Conductivity of Cu-Co-Si Alloys

Evolutions in precipitates, microstructure and properties of cold-worked CuNiCoSi alloy during short-time solid solution

Effects of Co/Si atomic ratio on hardness and electrical conductivity of Cu‐Co‐Si Alloys

Effect of Co Addition on Solidification Velocity, Hardness and Refined Structure Transformation Mechanisms of Undercooled Ni-Cu-Co Alloys

Microstructure and properties of Cu–Ni–Co–Si–Cr–Mg alloys with different Si contents after multi-step thermo-mechanical treatment

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Effect of Multistage Solid Solution Treatment on Microstructure and Properties of Al-6.5Si-5.5Cu-0.2Zr-0.01Sr-0.06Ti-0.2Y Alloy

Effects of aging treatment on mechanical and electrical properties of Cu-Co-(Ti) alloys

Effects of Si addition on mechanical, electrical and magnetic property of Cu-10Fe alloy

Accelerating heterogeneous nucleation to increase hardness and electrical conductivity by deformation prior to ageing for Cu-4 at.% Ti alloy

Significantly enhanced high-temperature mechanical properties of Cu-Cr-Zn-Zr-Si alloy with stable second phases and grain boundaries

Simultaneously enhancing the strength and electrical conductivity of Cu-Ni-Sn alloy through plastic deformation of an intermetallic compound

Effect of solid solution process on the structure and properties of Cu-Cr-Mg alloy in the aging state

CoTi Precipitates: the Key to High Strength, High Conductivity and Good Softening Resistance in Cu-Co-Ti Alloy

Enhanced hardness and moderate thermal conductivity of Cu-2.4Ni-0.7Si alloy processed via selective laser melting followed by suitable heat treatment