Abstract:In this work, the effect of Co addition on the solidification velocity, hardness and refined structure trans-formation of the undercooled Ni-Cu-Co alloys have been systematically investigated. The results show that the grain refinement of Ni-Cu-Co ternary alloys at low undercooling is caused by the intense dendrite remelting. However, the grain refinement at high undercooling is attributed to recrystallization, and the driving force of recrystallization comes from the stresses and plastic strains accumulated by the interaction between liquid flow induced by rapid solidification and primary dendrites. The Co addition can significantly increase the solidification velocity and recalescence effect of Ni-Cu-Co alloys by increasing the number of solidified crystal nucleus and solute diffusion velocity. Under the same undercooling level, the increase of solidification velocity and recalescence effect have strengthened the remelting effect and stress accumu-lation, which can enlarge the critical range for grain refinement gradually. Meanwhile, due to the significant improvement of solidification velocity and stress-induced deformation effect by Co addition, the low angle GBs in the refined structure of Ni-Cu-Co alloys increase and the grain size decreases significantly, which have significantly improved the average hardness of the refined structure. When Co addition reaches 6 %, the refined structures can appear in almost the whole undercooling range and the hardness are improved by more than 100 % compared with the as-cast structure.(c) 2022 Elsevier B.V. All rights reserved.

Combined experimental and computational investigation of precipitation behaviour and mechanical properties in a novel Cu–Ni–Si–Co alloy: effect of solution treatment temperature

Simultaneously enhanced hardness and electrical conductivity in a Cu–Ni–Si alloy by addition of Cobalt

Simultaneously Enhanced Hardness and Electrical Conductivity in a Cu-Co-Si Alloy by Optimizing Solid Solution Treatment

Investigation of Microstructure and Wear Properties of Precipitates-Strengthened Cu-Ni-Si-Fe Alloy.

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

CoTi Precipitates: the Key to High Strength, High Conductivity and Good Softening Resistance in Cu-Co-Ti Alloy

Effect of Co Addition on Solidification Velocity, Hardness and Refined Structure Transformation Mechanisms of Undercooled Ni-Cu-Co Alloys

Study on Precipitation in (cocrfemnni)90al6ti4 High Entropy Alloy

Microstructure and Precipitate's Characterization of the Cu-Ni-Si-P Alloy

Effects of Co/Si Atomic Ratio on Hardness and Electrical Conductivity of Cu-Co-Si Alloys

The Microstructure Evolution and Dynamic Recrystallization Mechanism of Cu-1.1–Ni-0.7–Co-0.45–Si-0.3Cr Alloys during High-Temperature Deformation

Precipitation behavior and microstructural evolution during thermo-mechanical processing of precipitation hardened Cu-Hf based alloys

Effect of Aging Temperature on Microstructure and Properties of Cold-Rolled Cu-Ni-Si Alloy

Effect of temperature on mechanical behavior of Cu–Cr–Co–Ti alloys

Effects of Co/Si atomic ratio on hardness and electrical conductivity of Cu‐Co‐Si Alloys

Microstructure and Property Evolution of Cu–9Ni–6Sn-xCr Alloys During Thermo-Mechanical Treatment Process

First-principles study on the high-strength and high-conductivity modification mechanism of C7035 copper alloy by Ni, Si, and Co solid solution

Effects of Co Addition on the Microstructure and Properties of Elastic Cu-Ni-Si-Based Alloys for Electrical Connectors

Effects of co-addition of Ni and Al on precipitation evolution and mechanical properties of Fe-Cu alloy

Evolutions in precipitates, microstructure and properties of cold-worked CuNiCoSi alloy during short-time solid solution

Microstructure and properties of Cu–Ni–Co–Si–Cr–Mg alloys with different Si contents after multi-step thermo-mechanical treatment