Abstract:Quartz Crucibles with large sizes are widely used in the production of rods for monocrystalline silicon in photovoltaic industry. Defects on the inner surface of aspheric crucibles should be removed at a high material removal rate (MRR), and atomic surface is strictly demanded. This is a challenge for chemical mechanical polishing (CMP), because of that CMP is usually applied to flat surface, rather than aspheric surface. Furthermore, traditional CMP normally employs noxious slurries, resulting in the potential pollution to the environment. To solve these challenges, a novel green CMP was developed, containing ceria, ytterbia, hydrogen peroxide, guar gum, potassium carbonate and disodium ethylenediamine tetraacetate. After CMP, atomics surface was achieved with surface roughness Sa of 0.122 nm at a measurement area of 100 x 100 mu m2, and the MRR is 31.56 mu m/h. Thickness of damaged layer is only 2.55 nm confirmed by transmission electron microscopy (TEM), which is the lowest value compared with those published previously. The developed CMP was applied to aspheric crucibles with a diameter of 810 mm, thickness of 15 mm and height of 580 mm. The surface roughness Sa of 0.361 nm was obtained, which is one order of magnitude lower than 2.648 nm through conventional mechanical polishing. Molecular dynamics (MD) simulations of nanoindentation and nanoscratch reveal that damaged layer was formed by densification of atoms at the surface. X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy elucidate the mechanisms of developed green CMP. The content of trivalent Ce3+ increases, through the reduction of hydrogen peroxide and induction of trivalent oxides of rare earths, such as ceria and ytterbia. Experimental results confirm that content of Ce3+ was enhanced to 37.75 %, and the MRR was improved about 54.77 %. During CMP, a soft silicate layer was generated, which is easy to be removed by abrasives of rare earth oxides. At the same time, Ce-O-Si groups were formed via the dehydration and condensation between Si-OH and Ce-OH groups. The two -OH groups were formed by hydroxylation during CMP, and Ce-O-Si groups could be removed easily. With the coupling between chemical and mechanical functions, atomic surface was achieved at a high MRR. Our findings provide new insights to produce atomic surface on aspheric quartz crucibles with large sizes at a high MRR, which is beneficial for photovoltaic industry.

Atomic surface of quartz glass induced by photocatalytic green chemical mechanical polishing using the developed SiO 2 @TiO 2 core–shell slurry

Atomic Surface of Quartz Glass Induced by Photocatalytic Green Chemical Mechanical Polishing Using the Developed SiO2@TiO2 Core–shell Slurry

Development of Core–shell SiO2@A-TiO2 Abrasives and Novel Photocatalytic Chemical Machinal Polishing for Atomic Surface of Fused Silica

Development of core–shell SiO 2 @A-TiO 2 abrasives and novel photocatalytic chemical machinal polishing for atomic surface of fused silica

Atomic-scale Planarization Surface of Quartz Glass Induced by Novel Green Chemical Mechanical Polishing Using Three Ingredients

Atomic Surface on Fused Silica Induced by Novel Green Photochemical Mechanical Polishing

Photocatalysis-Assisted Chemical Mechanical Polishing of SiC Wafer Using a Novel SiO2@TiO2 Core-Shell Composite Nanoparticles Slurry

Dispersion and Polishing Mechanism of a Novel CeO2-LaOF-Based Chemical Mechanical Polishing Slurry for Quartz Glass

A Novel Green CeO2 Polishing Slurry and Its Chemical Mechanical Action Mechanism for Achieving Atomic-Level Smoothing of Fused Silica Glass Surfaces

Effect of Surface Hydroxylation on Ultra-Precision Machining of Quartz Glass

Mechanism of chemical and mechanical mutual promotion in photocatalysis-assisted chemical mechanical polishing for single-crystal SiC

Investigation into Chemo-Mechanical Fixed Abrasive Polishing of Fused Silica with the Assistance of Ultrasonic Vibration

Effects of Pressure and Slurry on Removal Mechanism During the Chemical Mechanical Polishing of Quartz Glass Using ReaxFF MD

Investigation On Smoothing Silicon Carbide Wafer With A Combined Method Of Mechanical Lapping And Photocatalysis Assisted Chemical Mechanical Polishing

Atomic Surface of Fused Silica and Polishing Mechanism Interpreted by Molecular Dynamics and Density Functional Theory

Defect-free Surface of Quartz Glass Polished in Elastic Mode by Chemical Impact Reaction

Atomic Level Surface on Aspheric Quartz Crucible with Large Sizes Induced by Developed Green Chemical Mechanical Polishing with Composite Rare Earth Oxides

Achieving Ultralow Surface Roughness and High Material Removal Rate in Fused Silica Via a Novel Acid SiO2 Slurry and Its Chemical-Mechanical Polishing Mechanism

Study Using ReaxFF-MD on the CMP Process of Fused Glass in Pure H2O/aqueous H2O2

Angstrom surface with high material removal rate for quartz glass induced by silk dissolved novel green chemical mechanical polishing

Development of Electrical Enhanced Photocatalysis Polishing Slurry for Silicon Carbide Wafer