Abstract:As tellurides and selenides of Bismuth are extensively used thermoelectric materials in the low-temperature range with refrigeration application, A concerted effort is put forth to boost the ZT by co-doping the pristine Bi 2 Se 3 with antimony (Sb) on cation end and tellurium (Te) on anion side of the compound. The double sintered solid-state reaction method is employed in the preparation of Bi 2 Se 3 and (Bi 1− x Sb x ) 2 Se 2.7 Te 0.3 polycrystalline pellets, with x = 0.02, 0.04, and 0.06. The sample exhibits a rhombohedral structure with the space group of R m. FESEM and EDAX analysis are used to confirm surface morphology and elemental composition of the produced samples. The thermoelectric measurements for the pristine and co-doped samples were conducted by the physical property measurement system as well as a considerable increase in the Seebeck coefficient of − 115 μV/K is observed for 0.02 doping of the Sb which is 4.2 times greater than as for pristine (S = − 28 μV/K). Higher concentration doping ( x = 0.04, 0.06) has not reflected any Seebeck coefficient advancement. In contrast, the lowest total thermal conductivity at a low-temperature regime (< 50 K) is observed for x = 0.06 doping concentration which at near room temperature increases beyond the pristine thermal conductivity; whereas, x = 0.02, 0.04 doping concentration shows a decrement in total thermal conductivity at low, at room temperature region the values are almost equivalent to that of pristine. The co-doped samples' electrical resistivity is substantially less than pristine sample. The highest power factor of 3 × 10 –4 μW/mK 2 is obtained for the x = 0.02 sample. The highest ZT value for the x = 0.02 sample is almost 28 times more than a pristine sample. We conducted a study where we combined experimental and DFT methods to investigate thermoelectric properties incorporated into pristine and doped with antimony and tellurium on Bi 2 Se 3 . We have employed this combination to investigate the partial density of states, Seebeck coefficient, power factor using the Boltzmann transport equation. Theoretical thermoelectric data were derived and compared to experimental observations. Hence, using combined experimental and theoretical investigations helps to predict with higher accuracy of thermoelectric properties of semiconducting materials.

Enhancement of low-temperature thermoelectric performance via Pb doping in Cu3SbSe4

Band Engineering Through Pb‐Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4

Enhancement of thermoelectric performance of Cu 1.98 Se by Pb doping

Enhanced Thermoelectric Properties of Cu3SbSe4 Compounds by Isovalent Bismuth Doping

Effect of Pb Doping on the Thermoelectric Performance of Eco-Friendly Cu 3 SbS 4

Enhanced thermoelectric performance of BiCuSO by Pb doping and Se alloying

Ultralow Thermal Conductivity and Enhanced Figure of Merit for CuSbSe 2 via Cd-Doping

A comprehensive experimental and DFT analysis on thermoelectric properties of Sb, Te co-doped Bi2Se3 polycrystals

Defect Chemistry Engineering Promotes the Dopability of Cu for an Extraordinary Thermoelectric Performance of Hole-Doped PbSe with Resonant States

Enhancement of the thermoelectric properties of MnSb2Se4 through Cu resonant doping

Structural features and thermoelectric performance of Sb- and Bi-doped Cu2SnSe3 compounds

Doping-mediated stabilization of copper vacancies to promote thermoelectric properties of Cu2−xS

Unlocking the Potential of Cu3SbSe3: Ultralow Thermal Conductivity and Enhanced Thermoelectric Performance

Lattice expansion enables interstitial doping to achieve a high average ZT in n‐type PbS

Complex lattice occupation of copper leading to enhanced thermoelectric performance in n-type PbSe

Robustly Boosting Thermoelectric Performance of N‐Type PbSe via Lattice Plainification and Dynamic Doping

Enhanced thermoelectric performance of BiCuSeO through composite structuring with Pb-and La-doped components

Tuning Ag content to achieve high thermoelectric properties of Bi-doped p-type Cu3SbSe4-based materials

Modulated Fermi Level and Relaxed Lattice Strain Leading to Enhanced Thermoelectric Properties in AgSbSe 2

Thermoelectric properties and transport mechanism of Cu0.5In0.5Cr2Se4 and its Zn-doped samples

Highly Enhanced Thermoelectric and Mechanical Properties of Bi-Sb-Te Compounds by Carrier Modulation and Microstructure Adjustment