Abstract:In this study, CoMn2O4 and Cu0.5Co0.5Mn2O4 spinels are examined as protective coatings for chromium diffusion in metallic interconnect of solid oxide fuel cell. Both spinels are prepared by co-precipitation technique in order to obtain high temperature conducting spinels. The spinels obtained after 4 h of calcinations in air at 500 °C exhibit tetragonal crystal structure with average grain size between 90 and 100 nm. Cu0.5Co0.5Mn2O4 spinel exhibits superior electrical conductivity over CoMn2O4 and both display NTCR (negative temperature co-efficient of resistance) behavior illustrating their use as a protective layer on interconnects for fuel cells operating at higher temperatures. Doctor-blade employed spinel coating over SUS430 alloy exhibits good adhesion between protective spinel layer and metallic alloy. Cross section micrographs reveal presence of nanosized and highly dense grains capable to resist the outflow of chromium ions present in SUS430. Mass gain and diffusion rate constant (Kp) was high for CoMn2O4 coated SUS430 illustrating Cu0.5Co0.5Mn2O4 spinel as a better protective coating layer for interconnect application. Chromium outflow is restricted and the same is evident from all cross-section micrographs of spinel coated SUS430 specimens subjected for oxidation up to 1000 h. Estimated thickness of Cr2O3 layer was ∼15 nm for CoMn2O4 whereas Cu0.5Co0.5Mn2O4 coated SUS430 specimen had ∼12.5 μm thickness at the SUS430/spinel interface demonstrating superior resistance to chromium outflow. The area specific resistance was lowest for Cu0.5Co0.5Mn2O4 coated specimen (between 14 mΩcm2 – 15 mΩcm2) followed by CoMn2O4 coated specimen reiterating Cu0.5Co0.5Mn2O4 as efficient protective coating material for SUS430 SOFC interconnect.

The suitability performance of Sr2Fe1.5Mo0.5O6-δ-coated SUS430 for SOFC interconnect application

High Temperature Oxidation Behavior of SUS430 SOFC Interconnects with Mn-Co Spinel Coating in Air

The electrical property of MnCo2O4 and its application for SUS 430 metallic interconnect

Performance and In-Situ Densification of Mn-Co Spinel Coating on SUS430/441 Interconnect by Spraying Method

Supersonic spray derived Cu–Co oxide coating on SUS441 to protect the metallic interconnect and to increase stability of SOFC cathode

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

Characterization of the conductive protection layers on alloy interconnect for SOFC

Evaluation of SUS430 with Mn-Co Coating As SOFC Interconnect in Reducing Atmosphere

Evaluation of Protective La0.67Sr0.33MnO3–δ Coatings on Various Stainless Steels Used for Solid Oxide Fuel Cell Interconnects

The Preparation and Properties of Ti(Nb)-Si-C Coating on the Pre-Oxidized Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect

CoMn2O4 and Cu0.5Co0.5Mn2O4 spinels as efficient protective coating layers on SUS430 for SOFC interconnect

Fabrication of Mn–Co Alloys Electrodeposited on AISI 430 Ferritic Stainless Steel for SOFC Interconnect Applications

Oxidation and electrical behavior of Ni-Mn3O4-La2O3-coated SOFC interconnect steel

High temperature oxidation and chromium volatilisation of AISI 430 stainless steel coated by Mn-Co and Mn-Co-Cu oxides for SOFC interconnect application

CrxN/Mn1.7Cu1.3 coating on ferritic stainless steel for solid oxide fuel cell interconnects

Influence of Cr deficiency on sintering, thermal expansion and electrical properties of La0.75Sr0.25Cr1−xO3−δ as a SOFC interconnect material

Development of Annealed Mn–Co and Mn–Co–Cu Coated AISI 430 Stainless Steels for SOFC Interconnect Application

Cu doped Mn-Co spinel protective coating on ferritic stainless steels for SOFC interconnect applications

Effect of MnCoNiFeCu Alloy on Oxidation Behavior and Electrical Performance of AISI 441 for SOFC Interconnect Application

Sputtered Fe1·5CoNi0.5 coating: An improved protective coating for SOFC interconnect applications