Abstract:AISI 430 stainless steel is used for interconnects in solid oxide fuel cells (SOFCs). One of the main problems with this steel is the formation of chromia scales during oxidation at high temperature and thus increasing electrical resistance. In order to solve such problems, a protective and conductive coating layer can be applied on interconnects. In this study, AISI 430 steel was coated by Ni–P–TiO2–ZrO2 composite coating. To evaluate the oxidation behavior, isothermal and cyclic oxidation tests were used at 800 °C. Area specific resistances (ASR) of uncoated and coated samples were also compared as a function of time during oxidation at 800 °C. Chemical composition and surface morphology of the samples were examined before and after oxidation by Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD). In isothermal and cyclic oxidation tests, coated samples showed lower weight gain due to the formation of Ni2P2O7, Ni3P2O8, and NiFe2O4 spinel. This spinel prevented outward Cr diffusion, and improved the oxidation resistance of the AISI 430 stainless steel substrate. The obtained result by cyclic oxidation revealed that the coated substrates were resistant against cracking and spallation. Also, the results showed that the formation of Ni2P2O7, Ni3P2O8, and NiFe2O4 spinel and also the presence of TiO2 and ZrO2 caused ASR reduction. ASR of Ni–P–TiO2–ZrO2-coated specimens after 300 h of oxidation at 800 ºC (14.21 mΩ cm2) was lower than the uncoated specimens (41.84 mΩ m2) after the same time of oxidation.

Effect of MnCoNiFeCu Alloy on Oxidation Behavior and Electrical Performance of AISI 441 for SOFC Interconnect Application

Effect of Submicron SiC Particles on the Properties of Alcocrfeni High Entropy Alloy Coatings

Fabrication of Mn–Co Alloys Electrodeposited on AISI 430 Ferritic Stainless Steel for SOFC Interconnect Applications

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Fabricating a MnCo coating to improve oxidation resistance and electrical conductivity of Crofer22H alloy as SOFC interconnect

The electrical property of MnCo2O4 and its application for SUS 430 metallic interconnect

Development of Annealed Mn–Co and Mn–Co–Cu Coated AISI 430 Stainless Steels for SOFC Interconnect Application

Performance and In-Situ Densification of Mn-Co Spinel Coating on SUS430/441 Interconnect by Spraying Method

Oxidation and electrical behavior of AISI 430 steel coated with Ni–P–TiO2–ZrO2 composite for SOFC interconnect application

Oxidation and electrical behavior of Ni-Mn3O4-La2O3-coated SOFC interconnect steel

Investigation of high‐entropy alloy derived spinel‐based layer for SOFC cathode‐side contact application

Influences of Composite Electrodeposition Parameters on the Properties of Ni-Doped Co-Mn Composite Spinel Coatings

Supersonic spray derived Cu–Co oxide coating on SUS441 to protect the metallic interconnect and to increase stability of SOFC cathode

Experimental Investigation of the Initial Stage of the Oxidation Mechanism of Co Coating for Solid Oxide Fuel Cell Interconnects at 650 °C

Characterization of the conductive protection layers on alloy interconnect for SOFC

High temperature oxidation and chromium volatilisation of AISI 430 stainless steel coated by Mn-Co and Mn-Co-Cu oxides for SOFC interconnect application

Cu doped Mn-Co spinel protective coating on ferritic stainless steels for SOFC interconnect applications

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

High Temperature Oxidation Behavior of SUS430 SOFC Interconnects with Mn-Co Spinel Coating in Air

Effect of Cu on the diffusion behavior and electrical properties of Ni-Co conversion coating for metallic interconnects in solid oxide fuel cells

Fe doped Ni–Co alloy by electroplating as protective coating for solid oxide fuel cell interconnect application