Abstract:Low costly ferritic stainless steels, especially the Cr2O3-forming alloys, are promising interconnect materials for solid oxide fuel cells (SOFCs) due to their thermal expansion compatibility with other cell components. However, the oxidation resistance of commercial ferritic stainless steels in the operating temperature range of 600-800 degrees C is not adequate, forming relatively thick, poorly conducting oxide scale on the surface of the stainless steel interconnect and decreasing the cell performance. Surface modification is necessary to improve the oxidation behavior and electrical property. The present study investigates the effect of a LaCoO3 protective coating by the sol-gel process on the intermediate temperature oxidation behavior of SUS 430 alloy, which is frequently considered as the interconnect material for SOFCs. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used to characterize the phase structure, surface morphology and composition of the coating and the oxide scale. The "4-probe" method was employed to determine the area specific resistance (ASR) of the surface oxides. Long-term thermally cyclic oxidation at 750 degrees C in air has shown that the oxidation kinetics obeys the parabolic rule with a rate constant of K=4.18x10(-15) g(2)/(cm(4).s), which is 1-2 orders of magnitude lower than that of the uncoated alloy, the LaCoO3 protective coating effectively suppresses the formation of Cr2O3 and slows down the growth of MnCr2O4 spinel. As a result, the oxidation resistance and electrical conductivity of the coated SUS 430 alloy are significantly enhanced, resulting in an ASR at 750 degrees C of only 3.13 m Omega.cm(2) after oxidation at 750 degrees C for 850 h in air and an extrapolated ASR of 21.5 m Omega.cm(2) for 4 x 10(4) h oxidation.

Evaluation of SUS430 with Mn-Co Coating As SOFC Interconnect in Reducing Atmosphere

High Temperature Oxidation Behavior of SUS430 SOFC Interconnects with Mn-Co Spinel Coating in Air

Oxidation of MnCu0.5Co1.5O4 Spinel Coated SUS430 Alloy Interconnect in Anode and Cathode Atmospheres for Intermediate Temperature Solid Oxide Fuel Cell

The electrical property of MnCo2O4 and its application for SUS 430 metallic interconnect

Performance and In-Situ Densification of Mn-Co Spinel Coating on SUS430/441 Interconnect by Spraying Method

Cyclic oxidation of Mn–Co spinel coated SUS 430 alloy in the cathodic atmosphere of solid oxide fuel cells

Investigation of MnCu0.5Co1.5O4 spinel coated SUS430 interconnect alloy for preventing chromium vaporization in intermediate temperature solid oxide fuel cell

Investigation of Anomalous Oxidation Behavior of SUS430 Alloy in Solid Oxide Fuel Cell Dual Atmosphere

Effect of Lacoo3 Coating on the Intermediate Temperature Oxidation Behavior of Sus 430 Metallic Interconnect

CrxN/Mn1.7Cu1.3 coating on ferritic stainless steel for solid oxide fuel cell interconnects

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Supersonic spray derived Cu–Co oxide coating on SUS441 to protect the metallic interconnect and to increase stability of SOFC cathode

CoMn2O4 and Cu0.5Co0.5Mn2O4 spinels as efficient protective coating layers on SUS430 for SOFC interconnect

NiMn2O4 Spinel As an Alternative Coating Material for Metallic Interconnects of Intermediate Temperature Solid Oxide Fuel Cells

The suitability performance of Sr2Fe1.5Mo0.5O6-δ-coated SUS430 for SOFC interconnect application

Mn 1.4 Co 1.4 Cu 0.2 O 4 spinel protective coating on ferritic stainless steels for solid oxide fuel cell interconnect applications

Oxidation behavior of Cu-doped MnCo 2 O 4 spinel coating on ferritic stainless steels for solid oxide fuel cell interconnects

Influence of Pre-Reduction on Microstructure Homogeneity and Electrical Properties of APS Mn1.5Co1.5O4 Coatings for SOFC Interconnects

Effect of bias voltage on high-temperature oxidation resistance and electrical properties of Mn-Co coating with metal interconnects for solid oxide fuel cell

High temperature oxidation and chromium volatilisation of AISI 430 stainless steel coated by Mn-Co and Mn-Co-Cu oxides for SOFC interconnect application