Abstract:One of challenges in improving the performance and cost‐effectiveness of SOFCs (solid oxide fuel cells) is the development of suitable interconnects materials. Chromia‐forming alloys and especially ferritic stainless steels, like Crofer22APU, are considered to be among the most promising candidate materials as interconnects in SOFC stacks. However, the performance of chromia‐forming materials can be limited by the low electronic conductivity of the oxide scale (high ASR – area specific resistance – value). Such degradation are unacceptable regarding the long‐term operation (>40 000 h). A previous study 1 demonstrated that in air, the addition of a nanometric reactive element oxide (La2O3) layer applied by metal organic chemical vapor deposition (MOCVD) drastically improved both corrosion rate and electrical properties of Crofer22APU and Haynes230 alloys for 100 h at 800 °C. In this present study coating performances were checked after 10 months (7500 h) and 20 months (15 000 h) at 800 °C in air. The corrosion products were carefully analyzed by SEM, EDX, and XRD. ASR measurements are realized after long time exposure. This study demonstrates that the Crofer22APU alloy has a good oxidation resistance after 15 000 h in air but this alloy has an ASR value equal to 0.370 Ω cm2. The coatings composed of a thin reactive element oxide such as La2O3 resulted in an important improvement in the high temperature oxidation resistance; the ASR values are equal to 0.154 Ω cm2. Haynes230 alloy has a better oxidation resistance but the formation of an insulating Al2O3/SiO2 layer could be detrimental.

Evaluation of Protective La0.67Sr0.33MnO3–δ Coatings on Various Stainless Steels Used for Solid Oxide Fuel Cell Interconnects

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Comparison of iron and copper doped manganese cobalt spinel oxides as protective coatings for solid oxide fuel cell interconnects

Plasma spray coating on interconnector toward promoted solid oxide fuel cells and solid oxide electrolysis cells

CrxN/Mn1.7Cu1.3 coating on ferritic stainless steel for solid oxide fuel cell interconnects

Oxidation and electrical behavior of Ni-Mn3O4-La2O3-coated SOFC interconnect steel

Protective/Conductive Coatings on Ferritic Stainless Steels for Solid Oxide Fuel Cell Interconnect Applications

The Preparation and Properties of Ti(Nb)-Si-C Coating on the Pre-Oxidized Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect

Metallic Interconnects for Solid Oxide Fuel Cell: Performance of Reactive Element Oxide Coating During 10, 20 and 30 Months Exposure

Characterization of the conductive protection layers on alloy interconnect for SOFC

La–Cr coating deposited by DC magnetron sputtering for solid oxide fuel cell interconnect applications

Protective coating based on manganese–copper oxide for solid oxide fuel cell interconnects: Plasma spray coating and performance evaluation

Supersonic spray derived Cu–Co oxide coating on SUS441 to protect the metallic interconnect and to increase stability of SOFC cathode

Effects of Mn concentration on durability of Fe-Cr ferritic steels dispersed with La 2 O 3 for solid oxide fuel cell interconnects

The electrical property of MnCo2O4 and its application for SUS 430 metallic interconnect

Development of Coating Materials on Alloy Interconnect in Solid Oxide Fuel Cell

High Temperature Oxidation Behavior of SUS430 SOFC Interconnects with Mn-Co Spinel Coating in Air

Metallic interconnects for solid oxide fuel cell: Performance of reactive element oxide coating during long time exposure

Performance of stainless steel interconnects with (Mn,Co)3O4-Based coating for solid oxide electrolysis

Cu doped Mn-Co spinel protective coating on ferritic stainless steels for SOFC interconnect applications