Abstract:Ferritic stainless steels are candidate interconnect materials for solid oxide fuel cells (SOFC); however, the oxidation resistance of commercial stainless steels within the operating temperature range of 700–800°C is not adequate. A relatively thick, poorly conducting oxide layer forms on the surface of the stainless steel interconnect, decreasing cell performance. One way of modifying the oxidation behaviour of an alloy is through surface treatment. The aim of this work is to perform a systematic study of the effect of surface treatment (sandblasting and cold rolling) on the oxidation behaviour of three different ferritic stainless steels at 800°C in air. Oxidized specimens are characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). In addition, specimens oxidized under the same conditions for 15min are examined using secondary ion mass spectrometry (SIMS) depth profiling and X-ray photoelectron spectroscopy (XPS) depth profiling.For all three steels, the as-is (undeformed) specimens have a lower mass gain than the deformed specimens. The steel with the highest Cr content has significantly higher mass gains than the other two steels, which have similar mass gains. X-ray diffraction and electron microscopy results indicate that the oxide scale formed on all the specimens consists of an inner layer of chromia and an outer spinel layer. The relative amounts of the two oxide phases present depends on both the steel and treatment condition. The presence of insulating oxides at the metal/oxide interface is detected with both surface science techniques and electron microscopy.

Metallic Interconnects for Solid Oxide Fuel Cell: Performance of Reactive Element Oxide Coating During 10, 20 and 30 Months Exposure

Metallic interconnects for solid oxide fuel cell: Performance of reactive element oxide coating during long time exposure

Ni–Co/ZrO2 Composite Coatings via Electroless Plating on Crofer 22APU for SOFC Interconnect Applications: Oxidation and Chromium Vaporization Behavior

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Comparison of iron and copper doped manganese cobalt spinel oxides as protective coatings for solid oxide fuel cell interconnects

Evaluation of Protective La0.67Sr0.33MnO3–δ Coatings on Various Stainless Steels Used for Solid Oxide Fuel Cell Interconnects

Metallic Co with Reactive Element Oxide Composite Coatings for Solid Oxide Fuel Cell Interconnect Applications

Applying the Protective Mn–Co–La2O3 Coating on Crofer 22 APU Ferritic Stainless Steel Used as Solid Oxide Fuel Cell Interconnects

The effect of surface treatment on the oxidation of ferritic stainless steels used for solid oxide fuel cell interconnects

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

Performance of stainless steel interconnects with (Mn,Co)3O4-Based coating for solid oxide electrolysis

Protective coating based on manganese–copper oxide for solid oxide fuel cell interconnects: Plasma spray coating and performance evaluation

Degradation analysis of commercial interconnect materials for solid oxide fuel cells in stacks operated up to 18000 hours

CrxN/Mn1.7Cu1.3 coating on ferritic stainless steel for solid oxide fuel cell interconnects

Metallic Interconnect Materials Used in Solid Oxide Fuel Cell

Cr-Based Alloy Used as Interconnect in Solid Oxide Fuel Cells

Characterization of Metallic Interconnects Extracted from Solid Oxide Fuel Cell Stacks Operated up to 20,000 h in Real Life Conditions: The Air Side

Mechanical characterization of oxide coating–interconnect interfaces for solid oxide fuel cells

Supersonic spray derived Cu–Co oxide coating on SUS441 to protect the metallic interconnect and to increase stability of SOFC cathode

The Effect of Metallic Co-Coating Thickness on Ferritic Stainless Steels Intended for Use as Interconnect Material in Intermediate Temperature Solid Oxide Fuel Cells

Development and Application of HVOF Sprayed Spinel Protective Coating for SOFC Interconnects