Abstract:In order to realize SOFC as power generating devices, multiple cells are connected in series through an interconnect material to accumulate the voltage output. The interconnect should have very low permeability for the gases used. A novel solution combustion process has been developed for producing the phase pure, well-sinterable powders of Ca-doped LaCrO3 interconnect material. A process has been developed to produce the coarse granules as a feed material using combustion-synthesized powder for plasma spray through (a) preparation of granules through cold iso-static pressing followed by breaking and sieving (b) sintering of the green granules followed by sieving. The flow ability and deposition efficiency studies on +45-75 and 75-125 μm powders suggested that +45-75 powder is more suitable for the plasma spray coating. The plasma process parameters; plasma power, flow rate of carrier gases and distance between substrate and plasma gun have been optimized to achieve required coating characteristics. The as-produced coating using 20 kW power plasma gun on the porous Sr-doped LaMnO3 cathode substrates has been examined by SEM. An adherent coating of about 100 μm has been observed in the micrographs. No large cracks were observed throughout the coating. However, the coating was not found to be impervious in nature. Also the micrographs showed incomplete melting of the plasma-coated material. The similar experiments were performed using a higher power (≈ 60 Kw) plasma gun. The coated coupons were tested for leakage by checking water penetration. It was found that water did not penetrate for quite a long time. Therefore, the coupon was further tested for leakage by keeping it over a port connected to vacuum pump. The vacuum attained was 7×10-3 mbar and it was maintained for four consecutive days. The SEM studies on the coated sample showed a quite dense coating along with a very few small local pores.

La–Cr coating deposited by DC magnetron sputtering for solid oxide fuel cell interconnect applications

CrxN/Mn1.7Cu1.3 coating on ferritic stainless steel for solid oxide fuel cell interconnects

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Evaluation of Protective La0.67Sr0.33MnO3–δ Coatings on Various Stainless Steels Used for Solid Oxide Fuel Cell Interconnects

Supersonic spray derived Cu–Co oxide coating on SUS441 to protect the metallic interconnect and to increase stability of SOFC cathode

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

The Preparation and Properties of Ti(Nb)-Si-C Coating on the Pre-Oxidized Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect

Effects of Mn concentration on durability of Fe-Cr ferritic steels dispersed with La 2 O 3 for solid oxide fuel cell interconnects

Physicochemical Properties of (La,Sr)CoO3 Thick Films on Fe-25Cr Steel under Exposure to SOFC Cathode Operating Conditions

Applying the Protective Mn–Co–La2O3 Coating on Crofer 22 APU Ferritic Stainless Steel Used as Solid Oxide Fuel Cell Interconnects

Oxidation and electrical behavior of Ni-Mn3O4-La2O3-coated SOFC interconnect steel

Sputtered Fe1·5CoNi0.5 coating: An improved protective coating for SOFC interconnect applications

An investigation of Cr vaporization from SUS430 metallic interconnect and deposition on (La,Sr)MnO 3 cathode of intermediate temperature solid oxide fuel cells

Plasma spray coating on interconnector toward promoted solid oxide fuel cells and solid oxide electrolysis cells

Ni–Co/ZrO2 Composite Coatings via Electroless Plating on Crofer 22APU for SOFC Interconnect Applications: Oxidation and Chromium Vaporization Behavior

Fe doped Ni–Co alloy by electroplating as protective coating for solid oxide fuel cell interconnect application

Protective coating based on manganese–copper oxide for solid oxide fuel cell interconnects: Plasma spray coating and performance evaluation

Metallic Interconnects for Solid Oxide Fuel Cell: Performance of Reactive Element Oxide Coating During 10, 20 and 30 Months Exposure

Efficient FeCoNi/CeO 2 coatings for solid oxide fuel cell steel interconnect applications

Development of Ca-doped LaCr03 feed material and its plasma coating for SOFC applications

Cr-Based Alloy Used as Interconnect in Solid Oxide Fuel Cells