Abstract:HfO2-based resistive random-access memory (RRAM) with a Ti buffer layer has been extensively studied as an emerging nonvolatile memory (eNVM) candidate because of its excellent resistive switching (RS) properties and CMOS process compatibility. However, a detailed understanding of the nature of Ti thickness-dependent RS and systematic thermal degradation research about the effect of post-metallization annealing (PMA) time on oxygen vacancy distribution and RS performance still needs to be included. Herein, the impact of Ti buffer layer thickness on the RS performance of the Al/Ti/HfO2/TiN devices is first addressed. Consequently, we have proposed a simple strategy to regulate the leakage current, forming voltage, memory window, and uniformity by varying the thickness of the Ti layer. Moreover, it is found that the device with 15 nm Ti shows the minimum cycle-to-cycle variability (CCV) and device-to-device variability (DDV), good retention (105 s at 85 °C), and superior endurance (104). In addition, thermal degradation of the Al/Ti(15 nm)/HfO2/TiN devices under different PMA times at 400 °C is carried out. It is found that the leakage current increases and the forming voltage and memory window decrease with the increase in PMA time due to the thermally activated oxidation of the Ti. However, when the PMA time increases to 30 min, the Ti can no longer capture oxygen from HfO2 due to the formation of self-limited TiOx. Therefore, the device shows superior thermal stability with a PMA time of 90 min at 400 °C and no degradation of the memory window, uniformity, endurance, or retention. This work demonstrates that the Ti/HfO2-based RRAM shows superior back-end-of-line compatibility with high thermal stability up to 400 °C for over an hour.

Implementation of nitrogen-doped titanium-tungsten tunable heater in phase change random access memory and its effects on device performance

Ti/HfO2-Based RRAM with Superior Thermal Stability Based on Self-Limited TiOx

Electrothermal Simulation of Single-Walled Carbon Nanotube (Swcnt)-Based Phase Change Memory for 3-Dics

Investigation of Ni Doped Ge-Te Materials for High Temperature Phase Change Memory Applications

Electrothermal Modeling and Simulation of Resistive Random Access Memory (RRAM) with Different Resistive Switching Oxides

Highly electrical resistive SiTiN<i><sub>x</sub></i> heating layers and diffusion barriers for PCRAM

Thermal Stability and Electrical Resistivity of Sitanx Heating Layer for Phase-Change Memories

Localization of Joule Heating in Phase-Change Memory With Incorporated Nanostructures and Nanolayer for Reducing Reset Current

Phase-change Heterostructure Enables Ultralow Noise and Drift for Memory Operation.

Electrothermal Investigation on Vertically Aligned Single-Walled Carbon Nanotube Contacted Phase-Change Memory Array for 3-D ICs

A Heating and Diffusion Barrier Based on TaSiNx for Miniaturized IC Devices

The Performance Of Ge2sb2te5 Material For Pcram Device

THE PERFORMANCE OF Ge 2 Sb 2 Te 5 MATERIAL FOR PCRAM DEVICE

Direct observation of phase-change volume in contact resistance change memory using N-doped Cr2Ge2Te6 phase-change material

Soret-Effect Induced Phase-Change in a Chromium Nitride Semiconductor Film

Improving the Electrical Performance of Resistive Switching Memory Using Doping Technology

Understanding of Thermal Engineering for Vertical Nanowire Phase-Change Random Access Memory Partially Wrapped by Low-Conductivity Layer

Study of geometric effect on phase change random access memory

Programming Current Density Reduction for Elevated-Confined Phase Change Memory with a Self-Aligned Oxidation TiWOx Heater

Nitrogen-induced improvement of resistive switching uniformity in a HfO2-based RRAM device

Dependence Of The Properties Of Phase Change Random Access Memory On Nitrogen Doping Concentration In Ge2sb2te5