Abstract:Customized porous Al2O3-ZrO2-mullite composites were designed and prepared by reaction sintering of zircon (ZrSiO4) and alumina (Al2O3) at sintering temperatures from 1400 to 1600 °C for 3 h. The mechanical properties, microstructural evolution, and reaction mechanisms of the composites were investigated. The reactions between ZrSiO4 and Al2O3 were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray spectrometer (EDS). The results indicate that ZrSiO4 and Al2O3 react and form ZrO2 and mullite. Sintering temperature has an important effect on the reaction process. At 1400 °C, Al2O3 reacts directly with SiO2 of ZrSiO4 to form mullite and ZrO2, which reduces the decomposition temperature of ZrSiO4 and promotes the decomposition of ZrSiO4. However, at 1600 °C, ZrSiO4 first decomposes to form SiO2 and ZrO2, and then generates mullite by the diffusion of Si. The migration of Si is the key factor for the formation of mullite. The thermal shock resistance of the composites can be significantly improved by phase transformation toughening of in-situ ZrO2. Therefore, increasing the proportion of ZrSiO4 can significantly improve the mechanical properties of sample. The residual ratio of the flexural strength after thermal shock exceeded 90%, when the mass ratio of ZrSiO4 to Al2O3 was 3:1. Besides, the addition of polymethyl methacrylate could improve the porosity of materials and has a direct effect on the thermal conductivity of composites.

Fabrication and Machinability of Mullite-ZrO 2 -Al 2 TiO 5 Ceramics

The Effects of Mineral Composition and Sintering Temperature on Synthetic Mullite

Graded Machinable Si3N4/h-BN and Al2O3/LaPO4 Ceramic Composites

Fabrication and Properties of Porous Mullite Ceramics from Directly Sintering Ceramic Microspheres

Machinable Ceramic Graded Composites

Microstructure and mechanical properties of AlN–hBN based machinable ceramics prepared by pressureless sintering

Fabrication of mechanically robust nanoporous ZrSiO4 ceramics at low temperature with a low doping level of Mn dopant

Preparation and properties of porous mullite-based ceramics fabricated by solid state reaction

3D printing of dense structural ceramic microcomponents with low cost: Tailoring the sintering kinetics and the microstructure evolution

Addition of h-BN for enhanced machinability and high mechanical strength of AlN/Mo composites

Fabrication and characterization of porous mullite ceramics with ultra-low shrinkage and high porosity via sol-gel and solid state reaction methods

Production of Low-Porous Mullite Ceramics Modified with Zirconium Oxide

Microstructure and mechanical properties of a porous ceramic composite with needle‐like mullite and zirconia

A Simple and Efficient Way to Prepare Porous Mullite Matrix Ceramics Via Directly Sintering SiO2-Al2O3 Microspheres

Preparation of SiC ceramics reinforced with in-situ generated mullite by microwave sintering

SPS Fabrication of Whisker and ZrO2 Co-toughened Mullite Ceramics

Fabrication and Hardening Treatment for SiC/AlN Ceramic Composites

Porous Mullite Ceramic Modification with Nano-WO3

Reaction mechanisms and properties of in situ porous Al2O3-ZrO2-mullite composites

Fabrication and Mechanical Properties of Homogeneous Zirconia Toughened Alumina Ceramics Via Cyclic Solution Infiltration and in Situ Precipitation

A novel aqueous gel-casting for fabricating Al2O3-bonded fibrous mullite ceramics