Abstract:High-strength ceramics were prepared from high alumina fly ash (HAFA) and activated alumina as raw materials with magnesia as a sintering additive. The growth kinetics and influence mechanism of secondary mullite whiskers were investigated. Meanwhile, the effects of the Al2O3/SiO2 mass ratio (A/S) and the amount of magnesia on the content and morphology of mullite in the green body were investigated, so as to emphasize the effect of the liquid phase in the sintering process on the growth of secondary mullite whiskers. The results showed that the aspect ratio of secondary mullite whiskers increased significantly after adding activated alumina to increase the A/S ratio of raw materials. When 30 wt% activated alumina was added, the mullite content increased by 5.39%, and the whisker length increased from 1.36 μm to 4.18 μm. The addition of magnesia improved the liquid phase formed during the sintering process and the K value method was used to determine the sintering liquid phase content under various conditions. It was observed that increasing the magnesia level by 1 wt% could raise the liquid phase content by 5–7%. When the total liquid content of the system was 30–40%, the growth activation energy in the diameter direction of the whisker reduced significantly, promoting the growth of secondary mullite whiskers along the C axis. The morphology of mullite gradually developed from fibrous to long columnar crystal, making it combine more densely with the green body matrix. Furthermore, the staggered long columnar mullite crystal structure changes the fracture mode of ceramics from intergranular to transgranular fracture, which fully uses the high mechanical strength of mullite. As a result, the fracture energy and strength of ceramics are significantly improved.

SPS Fabrication of Whisker and ZrO2 Co-toughened Mullite Ceramics

Analysis of Factors Affecting the Preparation of Mullite Whiskers from Silica-Rich Slag and Application Studies

Fabrication of Homogeneous Mullite-Based Fiber Porous Ceramics with High Strength and Porosity

Preparation And High-Temperature Strengthening Of Tetragonal Zirconia Mullite Whisker Composites

The Effect of ZrO2Fiber on the Flexural Toughness and Thermal Shock Resistance of the Mullite-10%vol.SiC Whisker Ceramic

Zirconia-Mullite Obtained from Co-Precipitated Zirconia-Mullite Composite Powders by Sps

The preparation of mullite foamed ceramics reinforced by in-situ SiC whiskers and their reinforcement mechanism

Preparation and Mechanical Properties of SiC Whisker and Nanosized Mullite Particulate Reinforced TZP Composites

Synergistic Toughening Effect of SiC Whiskers and Particles in ZrO2–Al2O3–SiC Ceramics

The Effect of SiC Whisker on the Sintering and Thermal Shock Resistance Property of ZrO2-mullite Ceramic

Properties and mechanism of mullite whisker toughened ceramics

Microstructure and Properties of Porous Anorthite/mullite Whiskers Ceramics with High Porosity

Fabrication and Properties of Porous Mullite Ceramics from Directly Sintering Ceramic Microspheres

MICROSTRUCTURE AND MECHANICAL PROPERTIES OF MULLITE(W)/TZP CERAMIC COMPOSITES

Fabrication of SiC whisker reinforced laminated Si3N4/BN ceramics by spark plasma sintering

In situ mullite whisker network formation for high strength and lightweight ceramic proppants

Fabrication of ZrO2 whisker modified ZrO2 ceramics by oscillatory pressure sintering

The effect of multiple factors on the synthesis of mullite whiskers based on the S-L-S mechanism and the comparison of strengthening performance

Mullite-corundum gas-permeable refractories reinforced by in-situ formed SiC whiskers

Reaction sintering of ZrSiO4/α-Al2O3 mixed powders with Y2O3 addition

Fabrication and Mechanical Properties of ZrO2–Al2O3–SiC(w) Composites by Oscillatory Pressure Sintering