Abstract:The transformation-assisted consolidation under pressure has been demonstrated to be a promising method to fabricate the nano or submicron polycrystalline ceramic materials. The high pressure suppresses the long-range diffusion of the atoms and, consequently, restrains the grain coarsening. The new phases produced at high pressure could show finer grains under the appropriate thermodynamic conditions, which are not subject to the grain size of the raw materials. Ceramic materials exhibit the existence of the transformations under certain thermodynamic conditions and the formation of new phases generally undergoes the nucleation and growth. In the present work, monoclinic microcrystal ZrO2 with average grain size of 2 µm and Y2O3 with average grain size of 50 nm were mixed in molar ratio of 97∶3. The preparation of the samples was carried out by sintering at 5.5 GPa and temperatures of 800–1700 °C using the high pressure cubic cell, and the sample characterization was performed via the X-ray diffraction, scanning electron microscope and transmission electron microscopy. It was found that the monoclinic and submicron tetragonal composite polycrystalline ZrO2 in bulk is obtained under high pressure and high temperature. The average grain size of tetragonal ZrO2 fabricated at 1200, 1400, 1600 and 1700 °C is (145±62) nm, (246±165) nm, (183±62) nm and (245±107) nm, respectively. The synthesis of the fine-grained polycrystalline materials by the transformation under high pressure can solve the problems of agglomeration, adsorption and grain coarsening caused by the nanopowders as the starting materials in the conventional approach, which would be an alternative route to fabricate the fine-grained polycrystalline materials with the enhanced performances.

Fabrication of mechanically robust nanoporous ZrSiO4 ceramics at low temperature with a low doping level of Mn dopant

Fabrication of Submicron Tetragonal Polycrystalline ZrO2 by the Transformation of Micro Monoclinic ZrO2 under High Pressure

A New Sintering Approach to Ceramics at Low Temperature from Ba(Zr X Ti 1- X )O 3 Nanoparticles Doped by ZnO

Microstructures and Enhanced Mechanical Properties of (Zr, Ti)(C, N)-Based Nanocomposites Fabricated by Reactive Hot-Pressing at Low Temperature

Enhanced Mechanical Properties and Oxidation Resistance of Zirconium Diboride Ceramics via Grain‐Refining and Dislocation Regulation

Fabrication and Strengthening of Porous Si3N4 Ceramics by Replacement of Oxide Phase with Si3N4 at Grain Boundary Through Carbothermal Nitridation

Preparation of Zrb2-Sic Ceramics by Single-Step and Optimized Two-Step Hot Pressing Using Nanosized Zrb2 Powders

Optimization of the structure and morphology of monoclinic phase nanoscale zirconium dioxide

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub>-SiCp ceramics

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO2–Al2O3-SiCp ceramics

Effects of ZrSiO4 content on properties of SiO2-based ceramics prepared by digital light processing

Preparation of Si3n4 Ceramics with High Strength and High Reliability Via A Processing Strategy

Temperature‐dependent mechanical and oxidation behavior of in‐situ formed ZrN/ZrO2‐containing Si3N4‐based composite

Fabrication and Mechanical Properties of Porous Silicon Nitride Ceramics from Low-Purity Powder

Low temperature fabrication of highly dense α‐Si3N4 ceramics

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

The Effect of Mn Addition on Phase Development, Microstructure and Microwave Dielectric Properties of ZrTi2O6–ZnNb2O6 Ceramics

Excellent High-Temperature Strength and Ductility of the ZrC Nanoparticles Dispersed Molybdenum

Microstructure and mechanical properties of Zr3Al3C5-based ceramics synthesized by Al-Si melt infiltration

Achieving high-strength, high-porosity and relatively low-shrinkage in extrusion-based 3D printed ZrO 2 ceramics by adjusting CaCO 3 addition and sintering temperature

Fabrication and Mechanical Properties of Nano-SiC-Oxide Composites