Abstract:Polycrystalline heterogeneities of grain growth, phase transformation and tensile properties are discussed by metallography, spectroscopy and fractography when choosing laser welding with butt-joint configuration to satisfactorily minimize effect of inappropriate weld pool shape on microstructure and mechanical properties of γʹʹ precipitation hardable nickel-based superalloy in aerospace industry. There is parabolic relationship between weld penetration and diffusion-limited nucleation, growth and coarseness of secondary dendrite arm spacing alongside fusion boundary through nonequilibrium solidification process, which is dendritically susceptible to grain growth variation and metallurgical discontinuities. The amount, size, morphology and distribution of nonequilibrium intermetallic phase near the dendrite boundaries are kinetically and thermodynamically rely on weld pool shape whose crystal structure is incoherent with γ solid solution austenite phase and increases preference for crack initiation and propagation of brittle intergranular and ductile dimple fracture failures to enormously contribute to losses of strength and ductility. Unsymmetrical keyhole weld is thermometallurgically inconvenient for amelioration of microstructure and mechanical properties on either side, and adversely mitigates resistance to hypereutectic-aided dendrite embrittlement. Beneficial grain refinement and suppression of detrimental nonequilibrium intermetallic phase at the same time are challenging. This problem is an integral part of inhomogeneous microstructure and mechanical properties. The finer grain size occurs, the larger grain boundary area is available for Laves/γ eutectic-type reaction and vice versa. Contributions of coarse grain kinetics and metallurgical reaction thermodynamics to weld disintegration and fracture failure mechanism of tensile properties are explained by microstructure characterization of multicomponent and multiphase weld. Finally, it is imperative to dendritically balance these important factors to minimize inevitable interface solidification products and anomalous substructure growth, and reasonably advance superior mechanical properties of reliable weld.

Weld Cracking in Directionally Solidified Inconel 738 Superalloy

Boundary Liquation and Interface Cracking Characterization in Laser Deposition of Inconel 738 on Directionally Solidified Ni-based Superalloy

Cracking Mechanism and Susceptibility of Laser Melting Deposited Inconel 738 Superalloy

Stray grain formation, thermomechanical stress and solidification cracking in single crystal nickel base superalloy welds

Controlling hot cracking in Ni-based Inconel-718 superalloy cast sheets during tungsten inert gas welding

Microstructural development in single crystal nickel base superalloy welds

Investigating crack formation in IN738LC Ni-based superalloy fabricated by laser powder-bed fusion process

Avoiding Cracks in Additively Manufactured Non-Weldable Directionally Solidified Ni-based Superalloys

Mechanisms of Heat-Treatment-Induced Cracking in Additively Manufactured IN738 Alloy

Alternatives to Reduce Hot Cracking Susceptibility of IN718 Casting Alloy Laser Beam Welds with a Mushroom Shape

Crack Inhibition of Non-Weldable Inconel 738 Alloy in Ultrasound-Assisted Laser Directed Energy Deposition

In-situ Observation of Solidification Cracking of Laser Dissimilar Welded Joints

Analysis of Cracks in the Electron Beam Welded Joint of K465 Nickel-Base Superalloy

Grain refinement and crack inhibition of hard-to-weld Inconel 738 alloy by altering the scanning strategy during selective laser melting

Analysis of liquation and solidification cracks in the electron beam welding of GTD-111 nickel-base superalloy joint

Analysis on the Microfissuring Behavior in the Heat-affected Zone of Electron-beam Welded Nickel-based Superalloy

Influence of Electron Beam Thermal Effect on Cracks Formation in Fused Region of Single Crystal Superalloys DD407

Laser Preheating for Hot Crack Reduction in Direct Metal Deposition of Inconel 738LC

Diffusion-limited Nonequilibrium Phase Transformation of Nickel/Aluminum Dissimilar Materials during Laser Welding Part I: Precipitation-strengthened Polycrystalline Nickel-based Superalloy

Research Status of Ductility-Dip Crack Occurring in Nuclear Nickel-Based Welding Materials

Welding hot cracking characteristics and fracture mechanisms of nickel‐based alloy NS1402 under different constraint conditions