Abstract:Nickel-based superalloys are subject to severe microsegregation and exhibit anisotropic properties during laser metal deposition (LMD), which restricts their wide application in the aerospace field. Thus, post heat-treatments must be investigated to further regulate the microstructure and mechanical properties of such components. The aim is to provide a comprehensive understanding of the effects of double-stage aging (DA) and solution plus double-stage aging (SDA) heat treatments on microstructure and mechanical properties of Hastelloy X superalloy sheets fabricated via LMD. The effects of DA and SDA heat treatments on the density, residual stress, phase composition, carbides precipitation behavior, dislocation structure, grain structure, and mechanical properties of the sheets were studied and in comparison with the as-deposited (AD) samples. The results showed that the DA heat treatment yielded a significant amount of lamellar and granular phases in the interdendrites and grain boundaries, whereas the anisotropic microstructure between the transverse and vertical planes was similar to that observed in the AD samples. These phases are mainly composed of Laves phase and carbides. However, the needle-like carbide phase was dispersedly precipitated within the grains and at grain boundaries, and exhibited full recrystallization and reduced dislocation density after SDA heat treatment. Consequently, the SDA samples presented superior strength-ductility balance to those of the AD and DA samples with irregularly shaped Laves phase and carbides owing to microstructural changes. For instance, the SDA heat treatment improved the ultimate tensile strength and fracture elongation of the vertical samples by up to 10.9% and 30.7%, respectively, whereas the microhardness decreased by 13.3% compared to the AD samples. The compressive residual stress of 98 MPa and tensile residual stress of 147 MPa were also observed on the surfaces of the SDA and AD samples, respectively. In addition, the SDA samples exhibited an almost isotropic tensile behavior in the vertical and horizontal directions as the epitaxially grown columnar grains transforms into equiaxed grains, as well as exhibited a prominent overall crystallographic texture. The effect of DA and SDA heat treatments on the mechanical properties were analyzed on the basis of stress–strain curves, hardening behavior, and multiple strengthening mechanisms.

TLP repaired IN738LC superalloy with uneven surface defect gap width after post heat treatment: Microstructure and mechanical properties

Diffusion Brazing Repair of IN738 Superalloy with Crack-Like Defect: Microstructure and Tensile Properties at High Temperatures

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Microstructure of diffusion-brazing repaired IN738LC superalloy with uneven surface defect gap width

The Effects of Borides on the Mechanical Properties of Tlpb Repaired Inconel 738 Superalloy

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

Microstructures and mechanical properties of Ti6Al4V alloy repaired by the technology of point-mode forging and laser repairing

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Boride Evolutionary Behavior and Mechanism in the TLP Repaired IN738 Superalloy with Crack-Like Defects

Improving Tensile Properties of Dissimilar TLP Bonding Joints of IN718 Nickel-Based Superalloy/316LN Austenitic Steel by Long-Term Post-bonded Homogenization Treatment

Effect of thermal cycles on laser direct energy deposition repair performance of nickel-based superalloy: Microstructure and tensile properties

Laser cladding repairing of directionally solidified nickel base superalloy and its tensile properties

Microstructure-Mechanical Properties Relation of TLP-Bonded FSX-414 Superalloy: Effect of Homogenization Design

Microstructure and tensile properties of transient liquid phase (TLP) sintering repaired Ti-6Al-4V alloys with large area hole defect

Effect of holding time on microstructure and mechanical properties of dissimilar γ'‐strengthened superalloys TLP joint

Additively manufactured crack-free nickel-based superalloys with synergistic strength and plasticity via grain refinement and striped oxides inhibition

Tailoring the microstructure and mechanical properties of laser metal-deposited Hastelloy X superalloy sheets via post heat-treatment

Investigating crack formation in IN738LC Ni-based superalloy fabricated by laser powder-bed fusion process

The effect of post-bond solution treatment and double aging on the microstructural evolution and mechanical properties of TLP-bonded IN718 joint

Study of the Crack and Porosity Regulation of a Non-weldable Ni-Based Superalloy Fabricated by Laser Powder Bed Fusion

Reducing cracking sensitivity of CM247LC processed via laser powder bed fusion through composition modification