Abstract:Boride particles of various sizes and morphologies were obtained by adjusting the boron content and solidification rate of castings in Ti-45Al-2Mn-2Nb alloys. The initial and deformation microstructures, as well as the tensile properties at 25 degrees C and 650 degrees C, were examined. Furthermore, the fracture behavior of the alloys and the influence of boride particle with different morphologies on the tensile properties were discussed. Boride particles are curved flaky in 0.5B alloys, and varied from straight rod/needle-like to curved ribbon-like with increasing cooling rates in 1B alloys. Abundant phase interfaces, along with the presence of growth stacking faults and lattice distortions, are prominently observed in curved flaky and ribbon-like boride particles. Conversely, straight boride particles exhibit better regularity, with fewer lattice distortions and a lower density of interfaces and stacking faults. At both 25 degrees C and 650 degrees C, samples containing flaky boride particles exhibit the highest yield strength but the lowest elongation, while samples containing rod/needle-like boride particles show the lowest yield strength but the highest elongation. Curved boride particles exhibited no deformation, while their interfaces with the matrix accumulated a significant volume fraction of dislocations. This accumulation of dislocations causes stress concentration and created sites for the initiation of cracks. Additionally, the larger surface area of flaky boride particles promotes the growth of larger cracks, thus reducing ductility. On the other hand, straight rod/needle-like particles underwent deformation, resulting in the formation of deformation stacking faults on (0001) of C32-TiB2 and (10 1) of B27-TiB, showing better deformation compatibility between the borides and matrix.

Boride Evolutionary Behavior and Mechanism in the TLP Repaired IN738 Superalloy with Crack-Like Defects

The Effects of Borides on the Mechanical Properties of Tlpb Repaired Inconel 738 Superalloy

Structural Evolution of Topologically Closed Packed Phase in a Ni-based Single Crystal Superalloy

TLP repaired IN738LC superalloy with uneven surface defect gap width after post heat treatment: Microstructure and mechanical properties

Microstructure of diffusion-brazing repaired IN738LC superalloy with uneven surface defect gap width

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Diffusion Brazing Repair of IN738 Superalloy with Crack-Like Defect: Microstructure and Tensile Properties at High Temperatures

Formation and Kinds of Boride on Microstructure Evolution and Mechanical Properties in Ti47.5Al2.0Cr2.0NbxB Alloys

Transient Liquid Phase Bonding of IC10 Single Crystal with GH3039 Superalloy Using BNi2 Interlayer: Microstructure and Mechanical Properties

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

Improving Tensile Properties of Dissimilar TLP Bonding Joints of IN718 Nickel-Based Superalloy/316LN Austenitic Steel by Long-Term Post-bonded Homogenization Treatment

Tensile Behavior of Cast Γ-Tial Alloys with Varied Boride Morphologies

Cracking Behaviour and Its Suppression Mechanisms with TiB2 Additions in the Laser Additive Manufacturing of Solid-Solution-strengthened Ni-based Alloys

Boride-induced Dislocation Channeling in a Single Crystal Ni-based Superalloy

Boride Zone Formation in Transient Liquid Phase Bonding of Pairings of Parent Superalloy Materials with Different Compositions and Grain Structures

Effect of Boron on Fatigue Crack Growth Behavior in Superalloy IN 718 at RT and 650°C

The effect of post-bond solution treatment and double aging on the microstructural evolution and mechanical properties of TLP-bonded IN718 joint

Coupling effects of SiC and TiB2 particles on crack inhibition in Al-Zn-Mg-Cu alloy produced by laser powder bed fusion

Microstructure evolution, deformation behavior and manufacture design of TiAl matrix composites reinforced with in-situ borides precipitation

The effect of boron addition on the deformation behavior and microstructure of β-solidify TiAl alloys

Transient Liquid Phase Diffusion Bonding of Ni3Al Superalloy with Low-Boron Nickel-Base Powder Interlayer