Abstract:This study focuses on the microstructural characteristics and mechanical response of the diffusion-bonded joints of Inconel 617 superalloy. The joints exhibited two types of interfacial microstructure involving the straight interface (i.e., bond line) and the interface with partial migration of grain boundaries (GB). The straight interface was composed of the GB of γ-Ni, M23C6 carbide and α-Al2O3 oxide. The M23C6 carbide was precipitated with a semi-coherence of 3 3 ̅ 3 M 23 C 6 / / 1 1 1 ̅ γ − Ni , and an amorphous interface was detected between the α-Al2O3 and γ-Ni phase. The migration of GB across the interface was mainly caused by dynamic recrystallization and strain-induced GB migration. In addition, the α-Al2O3 oxide was remained inside the migrated grain. The formation of the M23C6 and α-Al2O3 was governed by diffusion mechanism, and the γ′-Ni3Al phase was formed surrounding the α-Al2O3 due to the abundant diffusion of Al. The straight interface, particularly embedded with the hard particles (i.e., the M23C6 carbide and α-Al2O3 oxide), restricted GND slipping, resulting in concentration of stresses and initiation of cracks. The migrated interface, in contrast, effectively prevented crack propagation and induced crack deflection, supporting more continuous and uniform plastic deformation. The elongation of 51.2 % was obtained for the joint with partial migrated interface, reaching 71 % of the base metal. Nevertheless, the optimum impact toughness of the joints (20.38 J/cm2) was merely 24 % of the base metal, mainly affected by the remained straight interface.

Microstructure of diffusion-brazing repaired IN738LC superalloy with uneven surface defect gap width

TLP repaired IN738LC superalloy with uneven surface defect gap width after post heat treatment: Microstructure and mechanical properties

Diffusion Brazing Repair of IN738 Superalloy with Crack-Like Defect: Microstructure and Tensile Properties at High Temperatures

Effect Of Diffusion Time On The Interfacial Microstructures Between The Bni5 Braze And The Nickel-Based Single Crystal Dd407 Alloy

Wide Gap Brazing of IN 738 With Boron Free Ni-Co-Zr-Hf-Cr-Ti-Al Braze Alloy

Boride Evolutionary Behavior and Mechanism in the TLP Repaired IN738 Superalloy with Crack-Like Defects

The Effects of Borides on the Mechanical Properties of Tlpb Repaired Inconel 738 Superalloy

Microstructural Evolution and Mechanical Properties of Ti2AlNb/GH99 Superalloy Brazed Joints Using TiZrCuNi Amorphous Filler Alloy

Microstructure and properties of the C/C-superalloy brazed joint by Ni-based filler

Microstructures and Mechanical Behaviors of Ni-Based Single-Crystal Superalloy DD90 Joints Brazed with a Co-Based Interlayer

Diffusion Brazing of GH536 Polycrystalline Superalloy with IC10 Single Crystal Superalloy Using BNi-2 Interlayer

Microstructural characteristics and mechanical response of diffusion bonding Inconel 617 superalloy

Microstructure and Properties of Vacuum-Brazed Joints of 3D-Structured Ni718 High-Temperature Alloy Prepared by Selective Laser Melting

Experimental and Numerical Study of Transient Liquid Phase Diffusion Bonded DZ40M Superalloys

Microstructure and brazing mechanism of TiAl/Ni-based superalloy joints using Ti-Zr-Cu-Ni-Co-Mo-B filler metal with different cooling rates

Dual Beam Laser Fusion-Brazed Ti6Al4V/AA7075 Dissimilar Lap Joint: Crack Inhibition Via Inoculation with TiC Nanoparticles

Microstructure and properties of TLPB joints of IN718 with 3D waveform structure prepared by SLM

Interfacial Microstructure and Mechanical Characterization of Silicon Nitride/nickel-Base Superalloy Joints by Partial Transient Liquid Phase Bonding

Microstructure and mechanical properties of diffusion bonded single crystal to polycrystalline Ni-based superalloys joint

Effect of diffusion time on interfacial microstructure of TLP joints of DD6 single crystal superalloy

Effect of holding time on microstructure and mechanical properties of dissimilar γ'‐strengthened superalloys TLP joint