Abstract:This study presents a detailed investigation into the deformation behaviour and the factors affecting the strength and ductility of laser powder bed fusion (LPBF) Ni-based superalloy 718 (Inconel 718) in both as-printed and heat-treated conditions using in-situ SEM + EBSD. The results show that following post-deposition high homogenization temperatures, the columnar grain structure of the as-printed Inconel 718 alloy successfully transformed to a nearly uniform grain size and the subsequent aging processes facilitated the precipitation of strengthening phases (gamma ', ' , gamma"). The specimen subjected to heat treatment (HT1) exhibited higher strength but lower ductility, while the as-printed specimen shows higher tensile elongation due to high initial dislocation density. In contrast, the heat-treated (HT2) specimen presented a more optimal combination of strength and ductility. The underlying mechanism for the enhanced tensile properties in the HT2 specimen was nearly homogeneous deformation trend across the grains and ultrafine precipitation of hardening phases. In addition, the twin boundaries were stable in the early deformation stages and maintained their orientation. Multiple slip systems were activated at the high-deformation stage, resulting in a high proportion of geometric necessary dislocations. Further, the interaction of deformation-induced dislocation with twin boundaries transformed them into general boundaries such as high and low-angle grain boundaries, ultimately increasing ductility. On contrary, in the HT1 specimen, the deformation inhomogeneity in grains enabled the strain localization at grain boundaries, which ultimately caused the early formation of cracks.

Improving Tensile Properties of Dissimilar TLP Bonding Joints of IN718 Nickel-Based Superalloy/316LN Austenitic Steel by Long-Term Post-bonded Homogenization Treatment

Reduction of ASZ size and enhancement of mechanical properties of TLP bonded IN718 joint using post bond heat treatment process

The effect of post-bond solution treatment and double aging on the microstructural evolution and mechanical properties of TLP-bonded IN718 joint

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

Effect of bonding time, composition of interlayer and post bond heat treatment on TLP joints of Inconel 718 superalloy

Effect of Post-Bond Heat Treatment on the Microstructure and High Temperature Mechanical Property of a TLP Bonded Γ′-Strengthened Co-Based Single Crystal Superalloy

Effect of holding time on microstructure and mechanical properties of dissimilar γ'‐strengthened superalloys TLP joint

Intergrowth Bonding Mechanism and Mechanical Property of Linear Friction Welded Dissimilar Near‐Alpha to Near‐Beta Titanium Alloy Joint

Effects of Post-Weld Heat Treatment on Microstructure and Mechanical Properties of TLP Bonded Inconel718 Superalloy

Enhanced Tensile Strength of Tial/Ti2alnb Diffusion Bonding Joint by a Novel Post-Bonded Hot Deformation

The Effects of Borides on the Mechanical Properties of Tlpb Repaired Inconel 738 Superalloy

Evolution of microstructure and mechanical properties on dissimilar transient liquid phase (TLP) bonding of GTD-111 and IN-718 by BNi-9 (AWS A5.8/A5.8M) interlayer

Influence of Post-Bond Heat Treatment on Microstructure and Creep Behavior of the Brazed Single-Crystal Nickel Superalloy

TLP repaired IN738LC superalloy with uneven surface defect gap width after post heat treatment: Microstructure and mechanical properties

Effect of Bonding Time on Dissimilar Transient Liquid Phase (TLP) Bonding of IN939 to IN625 Superalloys: Microstructural Characterization and Mechanical Properties

Achieving Balanced Mechanical Properties in Laser Powder Bed Fusion Processed Inconel 718 Superalloy Through a Simplified Heat Treatment Process

Microstructure evolution and tensile behaviors of dissimilar TLP joint of austenitic steel and high-Cr ferritic steel

Effect of transient liquid phase bonding followed by homogenization on the microstructure and hot tensile behavior of Inconel 738 superalloy

Influence of transient liquid phase bonding followed by homogenization on the fatigue lifetimes of inconel 738 at elevated temperature

Effect of bonding parameters on microstructures and properties during TLP bonding of Ni-based super alloy

Effect of Ti Powders Addition on Mechanical and Metallurgical Properties of IN718/BNi-2/316L Diffusion Couple