Abstract:This research aims to study the microstructure characteristics, mechanical properties, and corrosion behaviors of the dissimilar autogenous laser beam welded joint of pipeline steel (X-70) and super duplex stainless steel (sDSS 2507). Pipelines for the transmission of oil and gas and risers for offshore oil and gas drilling require this dissimilar joint. A dissimilar joint must maintain its properties and be defect-free under such challenging operating conditions. The microstructure of the interface, weld zone and heat-affected zone (HAZ) were all investigated thoroughly using optical microscopy (OM) and scanning electron microscopy (SEM) equipped with energy-dispersive spectroscopy (EDS). This dissimilar joint had significant microstructure anomalies in the weld and interfaces. Microstructure inhomogeneity's effect on welded joint mechanical properties, including microhardness, tensile and impact strength, was also studied. The linear potentiodynamic polarisation test in neutral 3.5 wt.% NaCl solution was used to study this weldment's corrosion behavior. The corroded surfaces were examined using an OM and SEM for the surface morphology investigation of corroded specimens. The macro-optical investigation has revealed full penetrations in the weld without any inclusions or porosities. The interface between the sDSS 2507 weld zone and the X-70 coarse grain heat-affected zone (CGHAZ) indicated a peak hardness of 418 Hv 0.5 . With an average of 345 Hv 0.5 , the WZ's hardness variation was reported to be in the 298–420 Hv 0.5 range. The hardness of the X-70/sDSS 2507 weld interface was assessed to be greater than that of the other region of weldments. An untempered martensitic region in WM and the CGHAZ of X-70, and the presence of M-A components are credited with the increase in hardness. The welded joint achieved reasonably excellent strength and ductility and met the marine and offshore standards requirements. The base metals and weldment for X-70 and sDSS 2507 have respective ultimate tensile strengths (UTS) of 610 ± 6 MPa, 995 ± 8 MPa, and 675 ± 10 MPa. The tensile findings revealed that the fracture location for weldment was evident in the X-70 base metal, ensuring that the weld metal was of adequate strength for the laser-weld joints. It was observed that the weldment's WM had the lowest impact strength. The Charpy impact toughness of the weld metal, however, was higher than both the ASME standard (> 41 J) and the EN 1599:1997 standards (> 47 J). The sDSS 2507 BM (310 ± 4 J) clearly outperforms the weld zones (185 ± 3 J) and X-70 base metal (295 ± 2 J) in terms of impact strength. The electrochemical corrosion test shows the corrosion potential, and the weld zone's corrosion rate is between sDSS 25,070 (− 260 ± 1.3 mV, 0187 ± 0.002 mm/year) and X-70 base metal (− 454 ± 1.8 mV, 0.321 ± 0.017 mm/year). Additionally, the surface morphologies and the electrochemical measurements matched significantly.

Studies on residual stresses and structural integrity of the dissimilar gas tungsten arc welded joint of sDSS 2507/Inconel 625 for marine application

GTAW Dissimilar Weldment of sDSS 2507 and Nickel Alloy for Marine Applications: Microstructure–Mechanical Integrity

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

Effect of filler metal composition on microstructural and mechanical characterization of dissimilar welded joint of nitronic steel and super duplex stainless steel

Investigation on microstructural and mechanical integrity of GTAW dissimilar welded joint of IN 718/ASS 304L using Ni-based filler IN 625 using EBSD and DHD techniques

Influence of filler materials on GTAW dissimilar welds: Inconel 718 and austenitic stainless steel 304L

Structure–property relationship assessment of dissimilar gas tungsten arc welded joint of pipeline steel and super duplex stainless steel for marine applications

Effect of Heat Input on Distortions and Residual Stresses Induced by Gas Tungsten Arc Welding in SS 316L to INCONEL625 Multipass Dissimilar Welded Joints

Evaluation of microstructural and mechanical properties of dissimilar Inconel 625 nickel alloy–UNS S32205 duplex stainless steel weldment using MIG welding

Analyzing microstructural, residual stress, and mechanical characteristics in dissimilar welds of Inconel 59 and AISI 904L through double-pulsed gas metal arc welding

Microstructural and mechanical investigation of dissimilar U-groove weld of IN 718/ASS 304L employing ERNiCr-3 filler

Residual stress analysis, microstructural characterization, and mechanical properties of tungsten inert gas-welded P92/AISI 304L dissimilar steel joints

Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study

Corrosion resistance of GTA-welded super duplex and nitronic steel in marine environments

CHARACTERIZATION OF MICRO STRUCTURAL AND MECHANICAL PROPERTIES OF INCONEL 625/A 517 HIGH STRENGTH QUENCHED AND TEMPERED STEEL DISSIMILAR WELDS

Experimental investigation on solidification cracking & intergranular corrosion of AISI 321 & AISI 316 L dissimilar weld on pulsed current gas tungsten arc welding (PCGTAW)

Structure–property relationships and corrosion behavior of laser-welded X-70/UNS S32750 dissimilar joint

Microstructure and tensile-shear behavior of dissimilar resistance spot welds between 2304 duplex stainless steel and Inconel 718 superalloy

Characterization of microstructure and mechanical properties of nickel based superalloy 617 by pulsed current gas tungsten arc welding technique

Microstructure and Mechanical Properties for the Dissimilar Joining of Inconel 718 Alloy to High-Strength Steel by TIG Welding

Mechanical and micro-structural studies of pulsed and constant current TIG weldments of super duplex stainless steels and Austenitic stainless steels