Abstract:Introduction The Biggest challenges coal-fired power plants are facing are improving their energy efficiencies and reducing their environmental impact due to CO2 and NOX emissions, can be attained by maximizing the steam pressure and temperature. However, the operating temperatures and pressures in boiler materials were restricted due to limited weldability of essential dissimilar joints between Austenitic Stainless Steel (ASS) and Creep-Enhanced Ferritic Steel (CEFS) due to carbon migration and sensitization. Present research work provides enhanced metallurgical and mechanical properties of weldment by optimizing the welding process and welding parameters. Aim The aim of the manuscript is to explores the welding compatibility of TP347H (stabilized ASS) with solution annealed T91 (CEFS), by Auto TIG welding technique, such that carbon migration at the fusion line of SA213 T91 and sensitization in the heat affected zone of TP347H can be minimized. Methods Influence of Auto TIG welding parameters on the mechanical, microstructure, and corrosion properties are studied and discussed. Carbon migration, mechanical and corrosion properties for lower (0.792 KJ/mm) and higher (1.124 KJ/mm) heat inputs weldments were compared. Investigation on mechanical properties test such as tensile, hardness, and root bend performed as per American Society of Mechanical Engineers (ASME) Section IX. Optical microscopy and Analytical Scanning Electron Microscope (SEM) coupled with Energy Dispersive Spectroscopy (EDS) have been performed to investigate carbon migration and sensitization behaviour. Sensitization susceptibility further validated by American Society for Testing and Materials (ASTM) A 262 Practice E. Results Investigation on tensile, hardness, and root bend tests revealed that mechanical properties for lower heat input weldment were superior. Restricted carbon migration due to optimized heat input improves mechanical properties and this was evidenced by satisfactory results of the bend test which showed no opening at the fusion line. A noticeable improvement in Ultimate Tensile Strength (UTS) 666 and 680N/mm2 (compared to 578 and 561N/mm2 for 1.124 KJ/mm heat input) and an acceptable hardness of 307 HV (compared to 399 HV for 1.124 KJ/mm heat input) were observed at T91 and weld metal interface. No fissures on bend surface and no Cr23C6 precipitation at grain boundary after performing ASTM A 262 Practice E and SEM-EDS respectively on heat affected zone (TP347H) of lower heat input weldment which shows higher resistance to intergranular corrosion (Sensitization). Conclusion Optimizing the welding parameters and decreasing the heat input mitigate the carbon migration at T91 fusion zone and, meeting the requirements for satisfactory mechanical properties in materials used for power generation applications. Further optimized welding heat input have lesser Cr23C6 precipitation in the heat-affected zone of TP347H, making the heat affected zone less susceptible to sensitization. Heat input must be controlled to (1) avoid intergranular corrosion failure or sensitization and (2) improve the mechanical properties of the weldment where requirement of post weld heat treatment is mandatory in the application (as recommended in the ASME Section 1, PW 39.1).

Effect of Heat Input on Distortions and Residual Stresses Induced by Gas Tungsten Arc Welding in SS 316L to INCONEL625 Multipass Dissimilar Welded Joints

Studies on residual stresses and structural integrity of the dissimilar gas tungsten arc welded joint of sDSS 2507/Inconel 625 for marine application

Effect of heat input on the mechanical and metallurgical aspects of double-pulse MIG welded IN 617

Heat Input Effect on Dissimilar Super Duplex Stainless Steel (UNS S32750) and Nitronic Steel (N 50) Gas Tungsten Arc Weld: Mechanism, Microstructure, and Mechanical Properties

Analyzing microstructural, residual stress, and mechanical characteristics in dissimilar welds of Inconel 59 and AISI 904L through double-pulsed gas metal arc welding

GTAW Dissimilar Weldment of sDSS 2507 and Nickel Alloy for Marine Applications: Microstructure–Mechanical Integrity

Influence of filler materials on GTAW dissimilar welds: Inconel 718 and austenitic stainless steel 304L

Investigation on microstructural and mechanical integrity of GTAW dissimilar welded joint of IN 718/ASS 304L using Ni-based filler IN 625 using EBSD and DHD techniques

Residual stress analysis, microstructural characterization, and mechanical properties of tungsten inert gas-welded P92/AISI 304L dissimilar steel joints

Experimental investigation on solidification cracking & intergranular corrosion of AISI 321 & AISI 316 L dissimilar weld on pulsed current gas tungsten arc welding (PCGTAW)

Evaluation of Residual Stresses and Distortion of Ti-5Al-2.5Sn and SS 304 Gas Tungsten Arc Welded Joints under Hybrid Thermal Tensioning Technique: Transient Thermal Tensioning and Trailing Intensive Cooling

Effect of Cr on the high-temperature corrosion of dissimilar AISI 904L and Inconel 625 joints employed in the coal-fired thermal power plant tubes

Comparison of metallurgical and mechanical properties of dissimilar joint of AISI 316 and Monel 400 developed by pulsed and constant current gas tungsten arc welding processes

Numerical Simulation Studies in Tungsten Inert Gas Welding of Inconel 718 Alloy Sheet

Effect of heat input on microstructure and mechanical properties of laser welded joint of Inconel 617 nickel-based superalloy

Microstructural and mechanical investigation of dissimilar U-groove weld of IN 718/ASS 304L employing ERNiCr-3 filler

The effect of heat input on weld-bead geometry, mechanical, phase transformation temperature, and corrosion properties of autogenous double pulse TIG welded nitinol sheets

Experimental Investigation on Single Pulse MIG Welding of Inconel 617

Experimental evaluation of longitudinal tensile properties of ferritic stainless-steel weldment joined by metal inert gas, pulse metal inert gas, and tungsten inert gas welding

Mechanical and intergranular corrosion properties of auto TIG welded TP347H-T91 dissimilar weldments

Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study