Abstract:Gas tungsten arc welding (GTAW) is a widely used process in marine and offshore applications to produce high-quality dissimilar welded joints (DWJs). However, the structural integrity of the welded joint depends on the heat input and filler metal application. This study investigated the microstructure–mechanical integrity and residual stresses of a multipass GTAW joint between super duplex stainless steel (sDSS 2507) and Inconel 625 (IN-625) utilizing ERNiCrMo-3 filler and two heat inputs (0.73 and 1.4 kJ/mm). This is a typical dissimilar joint found in oil and gas pipelines, and risers used to extract hydrocarbons. To understand the effect of the microstructure evolution on the mechanical behavior, the microstructure of the lower heat input (LHI) and higher heat input (HHI) weldments was compared. The optical image and secondary electron spectroscopy revealed an austenitic microstructure with an equiaxed, columnar, and cellular morphology in the LHI and HHI weld zones, with a Ni weight percentage of 52.40 pct. An unmixed zone (UZ) was found at the LHI and HHI weld zones and sDSS 2507 base metal interface but not at the IN-625 interface. NbC and Laves phases were found in the interdendritic region by energy-dispersive X-ray spectroscopy. Mechanical testing, including microhardness behavior, tensile properties, and impact toughness, was conducted in various weld regions following standard procedures at room temperature. The study also used deep hole drilling (DHD) methods to assess residual stresses of both LHI and HHI weld zone and determine whether heat input influenced these stresses. The LHI and HHI specimens' average ultimate tensile strength and percent elongation values were determined to be 800 ± 7 MPa and 27 ± 2 pct and 857 ± 5 MPa and 29 ± 3 pct, respectively. The microhardness maps demonstrated variations in the weld zones for both heat input weldments. The weld zone's hardness varied from 260 to 360 Hv 0.5 , with an average of 280 ± 6 Hv 0.5 for LHI and 300 ± 4 Hv 0.5 for HHI weldment. Impact toughness for the LHI weldment was 155 ± 3 and 160 ± 2 J for the cap and root regions, respectively, while it was 185 ± 7 and 195 ± 3 J for the HHI weldment. The DHD approach was utilized to analyze the distribution of residual stresses in the weld zone of both heat input weldments. Both the LHI and HHI joints showed a significant variation in residual stresses, with the HHI weldment exhibiting higher residual stress magnitudes for both tangential (21 pct) and longitudinal (23 pct) directions. The sDSS 2507/IN-625 DWJ was optimally fabricated without significant defects and with adequate mechanical performance to be considered for use in oil and gas pipelines and risers used in hydrocarbon extraction in accordance with ASTM specifications.

Comparison of metallurgical and mechanical properties of dissimilar joint of AISI 316 and Monel 400 developed by pulsed and constant current gas tungsten arc welding processes

Experimental investigation on solidification cracking & intergranular corrosion of AISI 321 & AISI 316 L dissimilar weld on pulsed current gas tungsten arc welding (PCGTAW)

Mechanical and micro-structural studies of pulsed and constant current TIG weldments of super duplex stainless steels and Austenitic stainless steels

Analyzing microstructural, residual stress, and mechanical characteristics in dissimilar welds of Inconel 59 and AISI 904L through double-pulsed gas metal arc welding

Investigation on microstructural and mechanical integrity of GTAW dissimilar welded joint of IN 718/ASS 304L using Ni-based filler IN 625 using EBSD and DHD techniques

Influence of filler materials on GTAW dissimilar welds: Inconel 718 and austenitic stainless steel 304L

Dissimilar autogenous TIG joint of Alloy 617 and AISI 304H steel for AUSC application

Effect of Cr on the high-temperature corrosion of dissimilar AISI 904L and Inconel 625 joints employed in the coal-fired thermal power plant tubes

Comparative Analysis of Microstructure Evolution and Mechanical Properties of Dissimilar Welded Joints of AA7075/AA6061 via Friction Stir Welding, Tungsten Inert Gas Welding, and Tungsten Inert Gas + Friction Stir Processing

Experimental Investigation On The Microstructure And Mechanical Properties Of Dss2205 And Ss304L Dissimilar Weldments

Comparative Research of Microstructure and Mechanical Properties of Stainless and Structural Steel Dissimilar Welds

Microstructural and mechanical investigation of dissimilar U-groove weld of IN 718/ASS 304L employing ERNiCr-3 filler

Dissimilar weldments of ferritic/martensitic grade P92 steel and Inconel 617 alloy: Role of groove geometry on mechanical properties and residual stresses

Study on Microstructural Characterization, Mechanical Properties and Residual Stress of GTAW Dissimilar Joints of P91 and P22 Steels

Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study

GTAW Dissimilar Weldment of sDSS 2507 and Nickel Alloy for Marine Applications: Microstructure–Mechanical Integrity

Residual stress analysis, microstructural characterization, and mechanical properties of tungsten inert gas-welded P92/AISI 304L dissimilar steel joints

Study and effect of GTAW parameters on mechanical properties of aluminium dissimilar welded joints: optimization technique

Localized Depth of Galvanic Corrosion at Dissimilar Metal Welding A508/Inconel 182/316L

Studies on residual stresses and structural integrity of the dissimilar gas tungsten arc welded joint of sDSS 2507/Inconel 625 for marine application

Cold Metal Transfer Welding of Ferritic and Austenitic Stainless Steel: Microstructural, Mechanical, and Electrochemical Studies