Abstract:The current study investigates the relationship between the microstructural and structural characteristics of dissimilar gas tungsten arc welding (GTAW) between Inconel 718 (IN 718) and austenitic stainless steel 304L (ASS 304L) using Inconel 625 (IN 625) as a filler material. The microstructural characterization of the dissimilar weld includes the application of an optical microscope (OM), field emission scanning electron microscopy (FE-SEM) including energy dispersive spectroscopy (EDS), and electron backscatter diffraction (EBSD). The optical and FESEM analysis of the base metals (BM) indicates the austenitic nature of the IN 718 BM matrix, which incorporates strengthening precipitates γ' and γ'' distributed throughout the Nickel matrix. In contrast, the ASS 304L BM exhibits an austenitic microstructure along with twins. Moreover, IN 625 weld metal exhibits austenitic microstructure in the form of cellular, columnar, and equiaxed dendrites. Elemental segregation demonstrates the existence of Nb, and Mo-rich carbides, including the laves phases at the interdendritic regions of the IN 625 weld zone and IN 718 Heat-Affected Zone (HAZ). Ferrite stringers were noticed in the HAZ of ASS 304L. EBSD analysis shows the improved texture of the weld zone exhibiting fine equiaxed recrystallized microstructures. EBSD/Kernel average misorientation (KAM) micrographs reveal the existence of high strain at the weld metal grain boundaries. Vickers microhardness assessment of the dissimilar weld demonstrates the high hardness of 257.5 HV for the IN 625 weld zone because of the occurred NbC, laves phases, and Mo-rich carbides. Room temperature tensile characterization shows the failure of tensile specimens from ASS 304L BM reflecting the high strength of the IN 625 weld metal (662 MPa). Tensile tests at high temperatures were performed at 550o C, 600o C, and 650o C. High-temperature tensile result exhibits a higher tensile strength of IN 625 weld zone than the ASS 304L BM, as the tensile specimens fails from 304L BM. The specimen exposed at 550o C exhibits the highest tensile strength of 388 MPa. The Charpy impact toughness test was conducted, with notches at the HAZ of ASS 304L, HAZ of IN 718, and the weld center being evaluated. The toughness value of the weld metal decreases (99 J) due to occurrence of the secondary precipitates. To analyze residual stress, the deep hole drilling (DHD) technique was used, which revealed that the peak residual stress (230 MPa) is induced at 6 mm from the weld surface and falls into the tensile stress category.

CHARACTERIZATION OF MICRO STRUCTURAL AND MECHANICAL PROPERTIES OF INCONEL 625/A 517 HIGH STRENGTH QUENCHED AND TEMPERED STEEL DISSIMILAR WELDS

Investigation on microstructural and mechanical integrity of GTAW dissimilar welded joint of IN 718/ASS 304L using Ni-based filler IN 625 using EBSD and DHD techniques

Evaluation of microstructural and mechanical properties of dissimilar Inconel 625 nickel alloy–UNS S32205 duplex stainless steel weldment using MIG welding

Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study

Investigation the effect of dissimilar laser welding parameters on temperature field, mechanical properties and fusion zone microstructure of inconel 600 and duplex 2205 stainless steel via response surface methodology

Analyzing microstructural, residual stress, and mechanical characteristics in dissimilar welds of Inconel 59 and AISI 904L through double-pulsed gas metal arc welding

Studies on residual stresses and structural integrity of the dissimilar gas tungsten arc welded joint of sDSS 2507/Inconel 625 for marine application

Effect of Welding Speed on Microstructure and Mechanical Properties of Selective Laser Melting Inconel 625 Alloy Laser Welded Joint

Effect of heat input on microstructure and mechanical properties of laser welded joint of Inconel 617 nickel-based superalloy

Influence of inconel interlayer on microstructural, mechanical and electrochemical characteristics in single-pass ATIG welding of dissimilar austenitic and duplex stainless steel

Microstructure and Mechanical Properties for the Dissimilar Joining of Inconel 718 Alloy to High-Strength Steel by TIG Welding

Dissimilar laser welding of an as-rolled CoCrFeMnNi high entropy alloy to Inconel 718 superalloy

Microstructure and Mechanical Properties of Inconel713C Ni3Al-based Superalloy Joint Welded by Electron Beam Feeding Wire Welding Technology

Microstructure and tensile-shear behavior of dissimilar resistance spot welds between 2304 duplex stainless steel and Inconel 718 superalloy

Experimental Investigation on Single Pulse MIG Welding of Inconel 617

Effect of laser welding parameters on the temperature distribution, microstructure and mechanical properties of dissimilar weld joint of Inconel 625 and stainless steel 304

Characterization of Mechanical Behavior in Solution-Treated Micro Plasma Arc Welded Blanks of Inconel 625

High-power fiber-coupled diode laser welding of 10-mm thick Inconel 617 superalloy

Dissimilar Welding of Inconel Alloys With Austenitic Stainless-Steel: A Review

Microstructural and mechanical investigation of dissimilar U-groove weld of IN 718/ASS 304L employing ERNiCr-3 filler

Friction Stir Lap Welding of Inconel 625 and a High Strength Steel