Abstract:Formability study on welded blanks of Nb-based refractory alloy C-103 (Nb-10Hf-1Ti (wt%)) has tremendous potential for utilizing smaller sheets for realization of large-size divergent portions of upper-stage liquid engine nozzle of satellite launch vehicles and thrusters of attitude orbital control systems. In this work, vacuum-annealed monolithic C-103 sheets were electron beam welded successfully to obtain defect-free welds and detailed microstructural and mechanical characterizations were investigated. Columnar epitaxial grains were found in fusion zone (FZ) instead of equiaxed grains in base metal (BM). Detailed SEM and HRTEM analyses revealed spherical shape of nano-size HfO 2 precipitates with monoclinic crystal structure in the C-103 sheet. Further, microhardness across the weld cross-section indicated that the FZ had a uniform and maximum hardness of ~195 HV 0.5 due to formation of finer nano-sized HfO 2 precipitates with higher number density, followed by a lowering of hardness in a narrow heat-affected zone. A marginal reduction in tensile strength of ~6 % with a considerable decrease in ductility of ~29 % was noticed for the welded sample. However, fracture occurred in the BM region, indicating good weld integrity. Furthermore, formability of the welded blanks was evaluated in terms of limiting dome height (LDH), forming limit diagram, and deep drawn cup depth. The effect of the presence of WZ on uniaxial, plane strain, and biaxial tensile strain paths on the formability of the C-103 sheet was estimated for the first time, and the results were compared with the monolithic sample. It was noted that the failure limit of the welded specimens decreased compared to that of the monolithic sample, resulting in a lower LDH of approximately 69 % and 62 % when deformed along plane strain and biaxial tensile strain paths, respectively. However, marginal variation in LDH was observed for the uniaxial strain path. Also, the welded blank had more resistance to material flow into the die cavity due to the harder weld region, resulting in a reduction of deep drawn cup depth by 52 % than that of the monolithic blank. The overall results concluded that the presence of the WZ significantly affected the formability of the C-103 sheet, especially in plane strain and biaxial strain paths. However, the fracture was never found to be propagating along the weld line, indicating the ability of the weld to sustain large plastic strains. This study provides insightful information on the formability of electron beam welded C-103 sheets for the successful fabrication of space components.

Characterization of Mechanical Behavior in Solution-Treated Micro Plasma Arc Welded Blanks of Inconel 625

Investigation on microstructural and mechanical integrity of GTAW dissimilar welded joint of IN 718/ASS 304L using Ni-based filler IN 625 using EBSD and DHD techniques

Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study

Investigation of Surface Residual Stress, Mechanical Properties, and Metallurgical Characterization of Inconel 625 Multilayer Thin-Wall Component Using Cold Metal Transfer Technique

Microstructure and mechanical properties of Inconel 686 fabricated by gas metal arc welding-based wire arc directed energy deposition: impact of cryogenic treatments

Location-dependent microstructure analysis and mechanical behavior of inconel 625 using Cold Metal Transfer(CMT) based wire and arc additive manufacturing

Microstructures and High Temperature Mechanical Properties of Electron Beam Welded Inconel 718 Superalloy Thick Plate

Effects of Solution Treatments on the Microstructure and Mechanical Properties of Inconel 625 Fabricated by Electron Beam Freeform Fabrication

Effect of Welding Thermal Treatment on the Microstructure and Mechanical Properties of Nickel-Based Superalloy Fabricated by Selective Laser Melting

CHARACTERIZATION OF MICRO STRUCTURAL AND MECHANICAL PROPERTIES OF INCONEL 625/A 517 HIGH STRENGTH QUENCHED AND TEMPERED STEEL DISSIMILAR WELDS

A Study on Microstructure and Mechanical Properties of Inconel 718 Superalloy Fabricated by Novel CMT-WAAM Process

Investigation of Single and Double Pulse Techniques on Microstructure and Mechanical Anisotropy of Inconel 686 Component Fabricated by Wire Arc Directed Energy Deposition

Microstructure and Mechanical Properties of Thick‐Walled Inconel 625 Alloy Manufactured by Wire Arc Additive Manufacture with Different Torch Paths

Microstructure and Fatigue Behavior of Cr-Mo Steel Weld Joints with Automatic TIG Welding

Comprehensive and Comparative Heat Treatment of Additively Manufactured Inconel 625 Alloy and Corresponding Microstructures and Mechanical Properties

Analyzing microstructural, residual stress, and mechanical characteristics in dissimilar welds of Inconel 59 and AISI 904L through double-pulsed gas metal arc welding

Studies on residual stresses and structural integrity of the dissimilar gas tungsten arc welded joint of sDSS 2507/Inconel 625 for marine application

Microstructure characterization and formability assessment of electron beam welded Nb-10Hf-1Ti (wt%) refractory alloy sheets

Mechanical Behavior of Laser Powder Bed Fusion Processed Inconel 625 Alloy

Microstructural Evolution and Mechanical Properties of Inconel 625 Alloy During Pulsed Plasma Arc Deposition Process

Effect of Heat Treatment on Microstructure and Mechanical Properties of Inconel 625 Alloy Fabricated by Pulsed Plasma Arc Deposition