Abstract:In this study, a butt-welded joint between P92 ferritic steel and SUS304 austenitic stainless steel was fabricated with a nickel-based filler material. Based on Sysweld software, three-dimensional thermal-metallurgical-mechanical coupled finite element analyses were performed to investigate the hardness and welding residual stress in the welded joint. In the material behavior model, various factors influencing the formation and distribution of hardness and welding residual stress were carefully considered, including the austenitic transformation, martensitic transformation, and the tempering of martensite in P92 steel; the isotropic strain hardening, annealing effect, and melting effect of all materials; and the differential thermal expansion between dissimilar metals. The neutron diffraction method and hole-drilling strain gauge method were applied to measure the profiles of residual stress of the welded joint, respectively. Hardness mapping was performed on a weld cross-section specimen. The predicted results of welding residual stress and hardness are in good agreement with the measurements, respectively. The peak residual stresses in longitudinal and transverse directions are above 600 MPa in P92 steel. There are high tensile residual stress and significant cold work near the weld root in SUS304 stainless steel. The solid-state phase transformation induces compressive longitudinal residual stress in the heat-affected zone, high tensile transverse residual stress near the weld toe in P92 steel, and a significant stress gradient. The tempering effect can reduce the hardness and tensile residual stress in the heat-affected zone of P92 steel. The formation mechanism of welding-induced residual stress was illustrated based on the Satoh test. The effects of peak temperature, internal restraint, and differential thermal expansion are found to be decisive for the formation of residual stress. Large tensile residual stress can be generated with internal restraints, which promote the stress increase and lead to material yielding. A restraint factor was proposed for the quantitative assessment of stress evolution.

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

DIC/DSI Based Studies on the Local Mechanical Behaviors of HR3C/T92 Dissimilar Welded Joint During Plastic Deformation

A study of local mechanical properties of 304L SS welded joints subjected to cyclic straining using depth-sensing instrumented indentation

Use of instrumented indentation testing to study local mechanical properties of 304L SS welded joints subjected to low-cycle fatigue loadings

DSI-based Studies of the Effects of High-temperature Aging on Local Mechanical Properties of HR3C/T92 Dissimilar Steel Welded Joint

Depth-sensing Indentation Measurement and Finite Element Analysis of Residual Stress Field Near Fatigue Crack Tip

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Modeling of welding residual stress in a dissimilar metal butt-welded joint between P92 ferritic steel and SUS304 austenitic stainless steel

Study on Residual Stress Distribution of 2024-T3 and 7075-T6 Aluminum Dissimilar Friction Stir Welded Joints

In situ studies of full-field residual stress mapping of SS304 stainless steel welds using DIC

Electromagnetic Ultrasonic Measurement for Welding Residual Stress Detection - Comparison Between Experiment with Numerical Simulation

Experimental Characterisation and Numerical Modelling of Residual Stresses in a Nuclear Safe-End Dissimilar Metal Weld Joint

Numerical Investigation of Formation Mechanism of Welding Residual Stress in P92 Steel Multi-Pass Joints

Fatigue Life of a Dissimilar Welded Joint Considering the Weld Residual Stress: Experimental and Finite Element Simulation

Predicting Welding Residual Stress of a Multi-pass P92 Steel Butt-Welded Joint with Consideration of Phase Transformation and Tempering Effect

Finite Element Analyses of Residual Stresses in Typical Welded Joints Used in Nuclear Power Plants and Comparisons with Experiments

Predicting Welding Residual Stresses in A Dissimilar Metal Girth Welded Pipe Using 3d Finite Element Model with A Simplified Heat Source

Residual Stress Distribution in A Dissimilar Weld Joint by Experimental and Simulation Study

Two-dimensional Mapping of Residual Stresses in a Thick Dissimilar Weld Using Contour Method, Deep Hole Drilling, and Neutron Diffraction

An approach for obtaining surface residual stress based on indentation test and strain measurement

Numerical Simulation and Experimental Verification of Residual Stress in the Welded Joints of Weldolet–Branch Pipe Dissimilar Steels