Abstract:To develop in-depth understanding of metallurgical phenomena for completeness, mechanical heterogeneity is kinetically and thermodynamically explained by thorough microstructure characterization of engineering materials, e.g. polycrystalline nickel-based superalloy, for alleviation of weldability-related problems during laser-induced keyhole fabrication. Because of nonequilibrium solidification behavior inside weld pool, finer γ phase dendrite substructure is confined to partition-resistant keyhole bottom part, coarser dendrite is crystallography-independently circumscribed at partition-vulnerable neck transition region of full penetration weld, and thus microstructure is lack of homogeneity. Abundance of segregation-driven eutectic phase or intermetallic phase in the interdendrite area throughout weld is essentially attributable to nonequilibrium solidification conditions, and morphologically increases susceptibility to mechanical properties deterioration. As a result of γ phase instability, Niobium-aided Laves/γ eutectic reaction in the vicinity of dendrite interstices at terminal stage of solidification contributes to severe dendrite boundaries brittleness, impairs mechanical properties, which is consistent with metallography and fractography results, and is more deleterious to weldability, since solute redistribution and supersaturation adversely exacerbate segregation behavior in the residual interdendrite liquid, especially asymmetric weld pool shape. There is inverse parabolic relationship between secondary dendrite arm spacing and solute partition coefficient, when location varies from nail-shaped weld upper site to bottom site. Chemical, microstructural and mechanical heterogeneities are more geometrically favorable in the curvature-related neck transition region. In addition, the mechanism of thermal, metallurgical and mechanical inhomogeneities, which are attributed to asymmetric weld pool shape, is consequently proposed. Untoward metallurgical phenomena, such as microstructure heterogeneity and brittle Niobium-rich Laves/γ eutectic phases mitigate strength, ductility and toughness of weld. In order to macroscopically and microscopically satisfy superior mechanical properties requirement, chemistry and microstructure of high quality weld are metallurgically controlled. Fruitful metallurgical information and mechanical data further support the reasonable explanations. It is imperative to progressively advance welding metallurgy, weldability and fabricability of intricate shape for welding defects minimization, suppress segregation and further develop mechanical properties through viable design and control of laser processing, simultaneously.

Analysis on the Microfissuring Behavior in the Heat-affected Zone of Electron-beam Welded Nickel-based Superalloy

Study on Microfissuring Damage of Ni-base Superalloy under Thermal Shock of Electron-beam Welding

Analysis of Cracks in the Electron Beam Welded Joint of K465 Nickel-Base Superalloy

Analysis of liquation and solidification cracks in the electron beam welding of GTD-111 nickel-base superalloy joint

Investigation of Microstructure and Hot Crack Formation Mechanisms in the Heat-Affected Zone of GTAW-Repaired Cast K4002 Nickel-Based Superalloy with HGH3113 Filler Metal

Microstructure and Properties of 3D-GH3625 Electron beam welded

Effect of texture evolution and defect on the crack initiation of a Ni‐based superalloy electron beam welded joint

In-situ investigation of microstructure-dependent deformation behavior of an electron-beam welded Ni Co based superalloy

Influence of Electron Beam Thermal Effect on Cracks Formation in Fused Region of Single Crystal Superalloys DD407

Study of Microstructure and Stress Corrosion Cracking Behavior in Welding Transition Zone of Ni-Based Alloys

Stray grain formation, thermomechanical stress and solidification cracking in single crystal nickel base superalloy welds

Microstructure evolution and fracture behaviour for electron beam welding of Ti-6Al-4V

Revealing the Fatigue Crack Propagation Mechanism of a Ni-based Superalloy Electron Beam Welded Joint Through In-Situ SEM Observation

Thermal, Metallurgical and Mechanical Determinants of Laminar Nickel/Aluminum Dissimilar Alloys during Laser-material Interaction Part I: Nickel-based Superalloy

Effect of heat input on microstructure and mechanical properties of IC10 Ni3Al-based superalloy electron beam welding joint

Microstructure Evolution And Fracture Behaviour For Electron Beam Welding Of Ti-W-4v

A Study of Crack and Fracture on the Welding Joint of Fe3Al and Cr18–Ni8 Stainless Steel

Diffusion-limited Nonequilibrium Phase Transformation of Nickel/Aluminum Dissimilar Materials during Laser Welding Part I: Precipitation-strengthened Polycrystalline Nickel-based Superalloy

Microstructure and Fatigue Crack Growth Behaviour of Electron Beam Welding in 30crmnsini2a Steel

Numerical simulation and experimental analysis of incomplete fusion mechanism of GH4169 and electroformed Ni electron beam welded joint

Crack generation mechanism and control method of electron beam welded Nb/GH3128 joint