Abstract:Passive isolation has been widely accepted as an effective means for the protection of structures against seismic hazards. The isolation bearings, typically placed at the base of the structure, increase the flexibility of the structure and shift its fundamental frequency away from the dominant frequency of seismic excitations, resulting in significantly reduced interstory drifts and floor accelerations. During severe earthquakes, the performance of passive isolation systems is usually achieved at the expense of having large base displacements. Alternatively, active isolation combines isolation bearings with adaptive actuators to effectively mitigate the base displacements, while maintaining reasonable interstory drifts and floor accelerations. Despite successfully theoretical proof documented in previous studies, most experimental implementations only verified active isolation with unit-axial actuators under unidirectional excitations. Earthquakes are intrinsically multidimensional, resulting in out-of-plane responses such as torsional responses. Therefore, the focus of this paper is the development and experimental verification of active isolation strategies for multistory buildings subjected to bidirectional earthquake loadings. First, a model building is designed to be dynamically similar to a representative full-scale structure. The selected isolation bearings feature low friction and high vertical stiffness, providing stable behavior. In the context of the multidimensional response control, three custom-manufactured and appropriately scaled actuators are employed to mitigate both in-plane and out-of-plane responses. In addition, the structure is subjected to multi-directional earthquake ground motion. To obtain a high-fidelity model of the active isolation systems, the authors propose a hybrid identification approach, which combines the advantages of the lumped mass model and nonparametric methods. Control-structure interaction is also included in the identified model to further enhance the control authority. By employing the H-2/LQG control algorithm, the controllers for the hydraulic actuators are shown to offer high performance and good robustness. Active isolation is found to possess the ability to reduce base displacements and produce comparable accelerations and interstory drifts to passive isolation. The proposed active isolation strategies are validated experimentally for a six-story building tested on the six-degree-of-freedom shake table in the Smart Structures Technology Laboratory at the University of Illinois at Urbana-Champaign. Copyright (c) 2013 John Wiley & Sons, Ltd.

Performance of a passive rate‐independent damping device in a seismically isolated multistory building

Experimental study of earthquake input energy of low‐frequency structures equipped with a passive rate‐independent damping device

Feasibility Study of a Novel Modal Decomposition Method for Low-Frequency Structure with Nonproportionally Distributed Rate-Independent Linear Damping

Horizontal Shaking Table Tests on a Four-Story Prototype Structure Using Multi-Dimensional Earthquake Isolation and Mitigation Devices

Multiaxial Active Isolation for Seismic Protection of Buildings

Influence of ground motion duration on seismic performance of RC frame isolated by high damping rubber bearings

Damping Identification of a Full‐scale Passively Controlled Five‐story Steel Building Structure

Application of Supplementary Inerter-Based Damping Devices Alongside Unbonded Fiber-Reinforced Elastomeric Isolators

Damped rigid substructure system for seismic protection of structures

Performance Study of an 8-story Steel Building Equipped with Oil Damper Damaged During the 2011 Great East Japan EarthquakePart 2: Novel Retrofit Strategy

Reliability Analysis of Reinforced Concrete Structure with Shock Absorber Damper under Pseudo-Dynamic Loads

Shaking Table Investigations on the Seismic Performance of a Steel Frame with Optimized Passive Energy Dissipation Devices

Seismic control of super high‐rise structures with double‐layer tuned particle damper

Potential use of rotational metallic dampers for seismic enhancement of infilled RC frames with open first story

Effect of displacement restraint on the collapse performance of seismically isolated buildings

Shake table tests and numerical investigation of a resilient damping device for seismic response control of building structures

A novel nonlinear isolated rooftop tuned mass damper-inerter (IR-TMDI) system for seismic response mitigation of buildings

Real-Time Hybrid Simulation of Multi-Story Structures Installed with Tuned Liquid Damper

Parameter optimization of vibration control system for adjacent building structures based on negative stiffness inerter damper

Seismic performance of structure equipped with a new rubber bracing damper system

Performance Evaluation of Distributed Extended KDamper Devices for Seismic Protection of Mid-Rise Building Structures