Abstract:Cu matrix composites have received increased attention in a wide industrial area because of their excellent mechanical properties and good electrical and thermal conductivity. However, the addition of general ceramic reinforcements often leads to a marked reduction in electrical conductivity for Cu matrix composites. In this study, the ZrB 2 -reinforced Cu composites have been developed to overcome this drawback since these metal borides possess relatively high electrical conductivity. The 5 wt.% ZrB 2 /Cu composites were prepared using hot-pressed sintering techniques at varying temperatures from 760 to 920°C. The influence of sintering temperature on the microstructure, relative density, and mechanical and electrical properties was examined. The results of the SEM observation show that ZrB 2 particles are seamlessly integrated into the Cu matrix for all ZrB 2 /Cu composites. The average grain size of the Cu matrix increases from 360 to 980 nm with the increase of the sintering temperature. The increase in sintering temperature also leads to the surface porosity decrease from 1.4 to 0.4%. The relative density and electric conductivity of the composites increase at the same time as the sintering temperature increases. However, microhardness increases and decreases, with a maximum value of 92 HV0.2 achieved at 840°C. The elastic modulus and nanohardness maps determined from the nanoindentation indicate that the reinforced ZrB 2 particles demonstrate the highest values for elastic modulus (340–500 GPa) and nanohardness (30–48 GPa). At the same time, the Cu matrix possesses a modulus of 100–200 GPa and nanohardness of about 10 GPa. TEM observation confirmed that the sintering temperature exhibits little influence on the interface reaction between ZrB 2 and Cu. Both sharp interface and interface with amorphous transition layer are observed. The variation of microhardness is mainly due to the strengthening of grain refinement and to the mismatch of the thermal expansion coefficients. The above results can provide further insights into the deeper understanding of the role of sintering temperature during hot-pressed sintering.

Microwave-assisted synthesis of Cu–ZrB2 MM Nano-composite using double pressing double sintering method

Microstructure and mechanical properties of Mo–Cu–Zr composites fabricated via microwave sintering

A comprehensive study of Al-Cu-Mg system reinforced with nano-ZrO2 particles synthesized by powder metallurgy technique

Synthesis and characterization of zinc oxide reinforced aluminum metal matrix composite produced by microwave sintering

Preparation of ZrB2-based Nanocomposites with Limited Grain Growth by Means of Low-Temperature Hot-Pressing Using Cu Additive

Nano-sized Amorphous Cu–Zr Alloy Particles Prepared by Mechanochemical Reaction

Enhanced Performance of AA7075/SiC/ZrC Hybrid Composite through Microwave Assisted Powder Metallurgy Techniques

Effect of Sintering Temperature on the Microstructure and Properties of High-Strength and Highly Conductive 5 wt.% ZrB2/Cu Composite

Two-step Hot Pressing of Bimodal Micron/nano-Zrb2 Ceramic with Improved Mechanical Properties and Thermal Shock Resistance

Exploring the Effects of Ball Milling and Microwave Sintering on Microstructural and Mechanical Behavior of AA7075/SiC/ZrO2 Hybrid Composites

The impact of Si3N4 incorporation on the mechanical characteristics of ZrB2-SiC nanocomposite sintered via pressureless method

Effect of Nano-Cu Particles on the Microstructure and Mechanical Properties of Cu/AZ31 Composites

Microwave-assisted Synthesis of Mo–Cu Nano-Powders at an Ultra-Low Temperature and Their Sintering Properties

Study on Microstructure and Properties of Cu-Zr Alloy Prepared by Mechanical Alloying

Pressureless Sintering of Zrb2-Sic Composites Strengthening by Ultra-Fine Ceramic Powders

Microstructures and Enhanced Mechanical Properties of (Zr, Ti)(C, N)-Based Nanocomposites Fabricated by Reactive Hot-Pressing at Low Temperature

Processing and Properties of ZrB<sub>2</sub>-Cu Composites Sintered by Hot-Pressing Sintering

Processing and Properties of ZrB2-Cu Composites Sintered by Hot-Pressing Sintering

Effect of ZrC nano-powder addition on the microstructure and mechanical properties of binderless tungsten carbide fabricated by spark plasma sintering

Improvement of mechanical performance on zirconium dioxide nanoparticle synthesized magnesium alloy nano composite

Synergistic strengthening mechanism and microstructural evolution of Al-Zn-Mg-Cu/ Al2O3/Y2O3 hybrid nanocomposite via mechanical alloying and hot pressing