Abstract:The present investigation has employed recycled waste glass powder (WGP) and silicon nitride (Si 3 N 4 ) as reinforcing-agents within AZ91D-matrix composites. The composites were fabricated by employing the vacuum stir casting technique to mitigate the effects of oxidation and to ensure homogeneity, uniformity, and superior wettability among the AZ91D-matrix and reinforcements. A microscopic study provided confirmation of a uniform dispersion of WGP and Si 3 N 4 particles throughout the AZ91D-matrix. The tensile strength of the AZ91D/WGP/Si 3 N 4 composites rise with the inclusion of WGP particulates by up to 1.5 percent in AZ91D/7.5% Si 3 N 4 . However, the tensile strength of the AZ91D/9%Si 3 N 4 composite have showed maximum value as compared to other chosen formulations/combinations in the current investigation. The tensile strength of AZ91D/1.5% WGP/7.5% Si 3 N 4 composites has strengthened up to 12.13 percent with the comparison of base alloy AZ91D-matrix. In A1 formulated composite, the amount of WGP particulate has enhanced the hardness of the AZ91D-alloy by up to 1.5 percent. Findings, nevertheless has exhibited that the A6 formulated composite had superior outcomes in terms of hardness. The incorporation of "reinforcing-constituent particulates" with 1.5%WGP + 7.5%Si 3 N 4 combination within the AZ91D-matrix, has further increased fatigue-strength by around 57.84 percent. A weight-loss of 0.312 mg was being unveiled for the A1 formulated fabricated composite. The weight-loss for the A6 formulated fabricated composite, however, was reported to be 0.294 mg. At 5 N loads, 2 m/s sliding speed, and 1000 m of sliding distance, the developed 1.5%WGP/7.5%Si 3 N 4 /AZ91D composites was reported to have a rate of wear, and frictional coefficient of 0.0025 mm 3 /m and 0.315, respectively. The investigation employing scanning electron microscopy (SEM) identified the presence of corrosion pits on the surfaces that had undergone corrosion. These pits were found to be a result of localised surface assaults occurring in corrosive environments. Additionally, SEM pictures of the worn surfaces indicated the emergence of microcracks, which may be associated to the conditions of cyclic loading. Moreover, the tensile-fractography examination for the developed 1.5%WGP/7.5%Si 3 N 4 /AZ91D composites has exhibited the brittle fracture failure, including cracks and debonding phenomena. In addition, the EDS spectra-analysis have revealed an apparent existence of the observed Mg-peak, Si-peak, Al-peak, Ca-peak, and O-peak for the 1.5%WGP/7.5%Si 3 N 4 /AZ91D composites. Furthermore, the utilisation of X-ray diffraction analysis effectively determined the existence of hard phases inside the AZ91D-matrix, which significantly contributed to the reported enhancement in wear resistance. The development of harder-phases has included, α-Mg, Al 12 Mg 17, SiO 2 , Si 3 N 4 , MgO, and CaO phases within the composite has been accountable for the enhancement of the tribomechanical, and wear-resistance characteristics of the AZ91D/WGP/Si 3 N 4 composites. The Si 3 N 4 has been discovered to have a substantial impact on enhancing mechanical performance and raising the resistance to wear.

Improvement of mechanical performance on zirconium dioxide nanoparticle synthesized magnesium alloy nano composite

A comprehensive study of Al-Cu-Mg system reinforced with nano-ZrO2 particles synthesized by powder metallurgy technique

Preparation and properties of nano ZrO2 coating on magnesium alloy

Nano-ZnO Particles’ Effect in Improving the Mechanical Response of Mg-3Al-0.4Ce Alloy

AZ63/Ti/Zr Nanocomposite for Bone-Related Biomedical Applications

Analysis and optimization of machining parameters of AZ91 alloy nanocomposite with the Influences of nano ZrO2 through vacuum diecast process

Synthesis and Experimental Investigations of Tribological and Corrosion Performance of AZ61 Magnesium Alloy Hybrid Composites

Al₂O₃ Nanoparticle Addition to Commercial Magnesium Alloys: Multiple Beneficial Effects

Microstructure and mechanical properties of friction stir welded AZ31 magnesium alloy reinforced with ZrB 2

Role of Nickel Particulate Reinforcement on Microstructure and Mechanical Performance of AZ31 Magnesium Composite

Mg/ZrO2 Metal Matrix Nanocomposites Fabricated by Friction Stir Processing: Microstructure, Mechanical Properties, and Corrosion Behavior

Effect of SiC Nanoparticles on AZ31 Magnesium Alloy

Hybrid Filler Actions on Functional Performance Evaluation of Magnesium Alloy (AZ61) Hybrid Nanocomposites

Enhancing tribo-mechanical, microstructural morphology, and corrosion performance of AZ91D-magnesium composites through the synergistic reinforcements of silicon nitride and waste glass powder

Effect of ZrO2p on the Microstructure and Mechanical Properties of the AZ31 Magnesium Alloy

Elevated Temperature Tribological Analysis and Mechanical Behavior of Ultrasonication-Assisted Stir-Squeeze-Casted ZE41–MWCNT Magnesium Nanocomposites

Refinement of the Magnesium-Aluminium Alloy Microstructure with Zirconium

The behaviour of AZ91 magnesium-based alloy with Ni–Al 2 O 3 reinforcement

Enhanced microstructure and mechanical properties of ZrN-reinforced AlSi10Mg aluminum matrix composite

AZ91D/TiB2 Nanocomposites Fabricated by Solidification Nanoprocessing

Synergistic effects of hybrid (SiC+TiC) nanoparticles and dynamic precipitates in the design of a high-strength magnesium matrix nanocomposite