Abstract:Cu matrix composites have received increased attention in a wide industrial area because of their excellent mechanical properties and good electrical and thermal conductivity. However, the addition of general ceramic reinforcements often leads to a marked reduction in electrical conductivity for Cu matrix composites. In this study, the ZrB 2 -reinforced Cu composites have been developed to overcome this drawback since these metal borides possess relatively high electrical conductivity. The 5 wt.% ZrB 2 /Cu composites were prepared using hot-pressed sintering techniques at varying temperatures from 760 to 920°C. The influence of sintering temperature on the microstructure, relative density, and mechanical and electrical properties was examined. The results of the SEM observation show that ZrB 2 particles are seamlessly integrated into the Cu matrix for all ZrB 2 /Cu composites. The average grain size of the Cu matrix increases from 360 to 980 nm with the increase of the sintering temperature. The increase in sintering temperature also leads to the surface porosity decrease from 1.4 to 0.4%. The relative density and electric conductivity of the composites increase at the same time as the sintering temperature increases. However, microhardness increases and decreases, with a maximum value of 92 HV0.2 achieved at 840°C. The elastic modulus and nanohardness maps determined from the nanoindentation indicate that the reinforced ZrB 2 particles demonstrate the highest values for elastic modulus (340–500 GPa) and nanohardness (30–48 GPa). At the same time, the Cu matrix possesses a modulus of 100–200 GPa and nanohardness of about 10 GPa. TEM observation confirmed that the sintering temperature exhibits little influence on the interface reaction between ZrB 2 and Cu. Both sharp interface and interface with amorphous transition layer are observed. The variation of microhardness is mainly due to the strengthening of grain refinement and to the mismatch of the thermal expansion coefficients. The above results can provide further insights into the deeper understanding of the role of sintering temperature during hot-pressed sintering.

Processing and Properties of ZrB<sub>2</sub>-Cu Composites Sintered by Hot-Pressing Sintering

Processing and Properties of ZrB2-Cu Composites Sintered by Hot-Pressing Sintering

Effect of Sintering Temperature on the Microstructure and Properties of High-Strength and Highly Conductive 5 wt.% ZrB2/Cu Composite

Research on Be/CuCrZr Bonding by Hot Isostatic Pressing at Intermediate Temperature

Microstructure and mechanical properties of hot pressed ZrC-SiC-ZrB 2 composites

Microstructure and Mechanical Properties of Reactive Hot-Pressed BN-ZrB_2-ZrO_2 Composites

Microstructure and high temperature mechanical properties of hot-pressed ZrB2-based composites

Microstructure and Mechanical Properties of ZrB2-SiC Composites

Mechanical, Corrosion and Wear Characteristics of Cu-Based Composites Reinforced with Zirconium Diboride Consolidated by SPS

Reactive hot pressing of ZrB2-SiC composites

Reactive Hot Pressing and Sintering Characterization of ZrB2–SiC–ZrC Composites

Reactive sintering behavior and enhanced densification of (Ti,Zr)B2–(Zr,Ti)C composites

Microstructural Features and Mechanical Properties of ZrB2–SiC–ZrC Composites Fabricated by Hot Pressing and Reactive Hot Pressing

Effect of sintering temperature on microstructure and properties of nano-WC particle reinforced copper matrix composites prepared by hot-pressing sintering

Pressureless Sintering of Zrb2-Sic Composites Strengthening by Ultra-Fine Ceramic Powders

Densification, microstructure and mechanical properties of ZrB2–SiCw ceramic composites

In situ reaction and solid solution induced hardening in (Ti,Zr)B 2 ‐(Zr,Ti)C composites

Study on Mechanical Properties of Hot Pressing Sintered Mullite-Zro2 Composites with Finite Element Method

Microstructure, Mechanical Properties and Oxidation Behavior of Reactive Hot-Pressed (Zr,Ti)B2-SiC-ZrC Composites

Microstructures and Enhanced Mechanical Properties of (Zr, Ti)(C, N)-Based Nanocomposites Fabricated by Reactive Hot-Pressing at Low Temperature

Microstructure and mechanical properties of hot pressed ZrB2–SiCp–ZrO2 composites