Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. The present-day structural application requires advanced materials at extreme conditions, and the development of it is not economically feasible. As a result, existing material in the composite form has more visibility to suit the purpose. The material's strengths and qualities must be examined before it can be recommended for use in harsh conditions. In the present study, Al2O3 (3, 6, 9, 12, and 15 wt.%) and ZrO2 particles (2 wt.%) are reinforced with Al-Mg-Si alloy (Al 6061), which possess good isotropic behaviour and better interface bonding. The double stir casting process was adopted for the hybrid composite development, and the samples were cold rolled to reduce grain size and pores in the composites. The developed composites were subjected to mechanical characterisation tests such as hardness, tensile, compression, impact and flexural tests. An increase in reinforcement percentage enhances the mechanical properties. The improvement was attributed to the high thermal mismatch and reduction in the inter-particle distance by cold rolling and the reinforcements. Scanning electron microscope microstructural examination was conducted, and even dispersion of 3 to 15 wt.% Al2O3 reinforcements was observed. Tensile elongation decreases with an increase in reinforcement percentage. High elastic modulus and temperature mismatch between matrix and reinforcements increase the strength of the composites. The fracture behaviour of the composites generally showed dimples which are characteristics of ductile fracture, except at 15 wt.% Al2O3 / 2 wt.% ZrO2 showed a large portion of cleavage planes and grain cracking. The Al-Mg-Si alloy is reinforced with 9 wt%. Al2O3 / 2 wt.% ZrO2 had the best properties suitable for its use in different structural applications.

Exploring the Effects of Ball Milling and Microwave Sintering on Microstructural and Mechanical Behavior of AA7075/SiC/ZrO2 Hybrid Composites

Enhanced Performance of AA7075/SiC/ZrC Hybrid Composite through Microwave Assisted Powder Metallurgy Techniques

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Mechanical milling and its influence on microstructure and electric conductivity of high mass fraction TiC / Cu composites

Mechanical and wear behavior of Al 7075/Al2O3/SiC/mg metal matrix nanocomposite by liquid state process

INFLUENCE OF MILLING TIME ON GROWTH MORPHOLOGY AND MECHANICAL PROPERTIES OF ALUMINUM-SILICON-CARBIDE COMPOSITES

Effect of ball milling time on the structural characteristics and mechanical properties of nano-sized Y2O3 particle reinforced aluminum matrix composites produced by powder metallurgy route

Microstructure and Mechanical Behavior of Microwave Sintered Cu50Ti50 Amorphous Alloy Reinforced Al Metal Matrix Composites

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Study of Microstructural and Mechanical Properties of Al/SiC/TiO2 Hybrid Nanocomposites Developed by Microwave Sintering

Influence of Silicon Carbide Reinforcements on Mechanical and Wear Behaviour AA7075/15% wt. Glass fiber Hybrid Composites

Synthesis and characterization of zinc oxide reinforced aluminum metal matrix composite produced by microwave sintering

Effect of milling time on microstructure and hardness of AA7075-15 wt% SiC-1 wt% MWCNT nanocomposite

Effect of ball milled Zr/Al/ZrB2 composite powders on microstructure and toughening of ZrB2–SiC/Zr–Al–C composite ceramics sintered by spark plasma sintering

Effect of Milling Time and Reinforcement Volume Fraction on Microstructure and Mechanical Properties of SiCp-Reinforced AA2017 Composite Powder Produced by High-Energy Ball Milling

Experimental investigation on the mechanical performance of the Al2O3 and ZrO2 added Al-Mg-Si alloy for structural applications

Fabrication of SiC reinforced aluminium metal matrix composites through microwave sintering

Role of Different Fractions of Nano-size SiC and Milling Time on the Microstructure and Mechanical Properties of Al–SiC Nanocomposites

Fabrication of Nano-Sic_p/al Composite by High Energy Ball Milling

Effect of Ball Milling Time on the Microstructure and Properties of High-Silicon–Aluminum Composite