Abstract:This study focuses on the effects of hybrid reinforcement consisting of nanosized particles of Palm Sprout Shell Ash (PSSA) and silicon carbide (SiC) on the mechanical and tribological properties of the Al-Cu-Mg alloy. Hybrid reinforced composites with different weight percentages of SiC and PSSA (0:0, 0:4, 1:3, 2:2, and 4:0 wt%) were prepared using the ultrasonic-assisted bottom-poured stir casting technique. Scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) were used to characterize the hybrid composite made of Al-Cu-Mg alloy. The optical and SEM microstructural analyses demonstrated an even distribution of SiC and PSSA nanosize reinforcements within the matrix. The EDS analysis revealed SiC and PSSA reinforcement particles in the composite. The mechanical properties (tensile, flexural, and impact strength) and wear properties (wear rate and coefficient of friction) of the composites and alloys were evaluated according to the ASTM standards. The hybrid reinforced composites outperformed the base alloy. Among all composites, the 2:2 wt% SIC and PSSA hybrid-reinforced composites exhibited a significant enhancement in both tensile and flexural strength, with a 22.64% and 27.64% increase in strength, respectively. However, the inclusion of these reinforcements led to a reduction in the ductility and impact strength of the Al-Cu-Mg alloy composite. The 0:4 wt% SiC- and PSSA-reinforced composites experienced the largest reductions in ductility and impact strength, with decreases of 47.67% and 4.38%, respectively. For the 2:2 wt% SiC and PSSA composites, these reductions were 23.64% and 3.19%, respectively. The SEM analysis of the fractured surfaces of the composites tested for mechanical properties revealed evidence of both ductile and brittle fracture mechanisms in the tensile, flexural, and impact tests. The wear behaviour of the prepared samples was evaluated, and all composites exhibited superior performance compared with the base alloy, demonstrating adhesive and abrasive wear mechanisms and varying friction coefficients. Among all the composites, the 2:2 wt% SiC- and PSSA-reinforced composites exhibited high wear resistance and a lower coefficient of friction than the other fabricated composites.

Influence of Silicon Carbide Reinforcements on Mechanical and Wear Behaviour AA7075/15% wt. Glass fiber Hybrid Composites

Effects of Silicon Carbide and Tungsten Carbide in Aluminium Metal Matrix Composites

Investigation on the effect of SiC and TiB2 ceramic particles on mechanical and tribological properties of Al7075 hybrid metal matrix composites prepared through conventional stir casting technique

Mechanical and wear behavior of Al 7075/Al2O3/SiC/mg metal matrix nanocomposite by liquid state process

A Study On The Effects Of Hybrid (Sic- Pssa) Nano Sized Reinforcement On Mechanical And Tribological Behaviour Of Al Alloy-Based Metal Matrix Composite Produced By Ultrasonic Assisted Stir Casting

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Synthesis and characterization of AA7075/SiC/graphene hybrid composite

Mechanical Characteristics and Wear Behaviour of Al/SiC and Al/SiC/B4C Hybrid Metal Matrix Composites Fabricated Through Powder Metallurgy Route

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Mechanical Properties of Aluminum-4043/Nickel-coated Silicon Carbide Composites Produced via Stir Casting

Dry sliding wear and viscoelastic performance of aluminum-based hybrid composites reinforced with SiC and metallic glass particles

Tribological Behavoiur of Silicon Carbide/ Rice Husk ash Reinforced Al7075 Hybrid Composites Using Optimization Techniques

Corrigendum: A study on the effects of hybrid (SIC- PSSA) nano sized reinforcement on mechanical and tribological behaviour of Al alloy-based metal matrix composite produced by ultrasonic assisted stir casting (2024 Mater. Res. Express 11 075010)

Microstructural, mechanical and corrosion behaviour of Al–Si alloy reinforced with SiC metal matrix composite

The effect of reinforcement particles weight percentage on the mechanical properties and plastic flow behaviour of aluminum alloy 7075 matrix material

Effect of SiC Weight Percentage on Tribological Characteristics of Al7075/SiC Composites

SiC and MWCNT Blending Actions on Functional Performance of Hybrid AA2024 Alloy Nanocomposite Via Two Step Stir Cast Route

Effect of B4C and SiC nanoparticle reinforcement on the wear behavior and surface structure of aluminum (Al6063-T6) matrix composite

Characterization of Al 5052 Based Metal Matrix Composites Reinforced with SiC and Al2O3

Investigation On Tensile Properties Of Aluminum 7075 - Silica Particles -Boron Fiber- Reinforced Hybrid Metal Matrix Composites

Effect of SiC Content on Mechanical and Tribological Properties of Al2024-SiC Composites