Abstract:This study focuses on the effects of hybrid reinforcement consisting of nanosized particles of Palm Sprout Shell Ash (PSSA) and silicon carbide (SiC) on the mechanical and tribological properties of the Al-Cu-Mg alloy. Hybrid reinforced composites with different weight percentages of SiC and PSSA (0:0, 0:4, 1:3, 2:2, and 4:0 wt%) were prepared using the ultrasonic-assisted bottom-poured stir casting technique. Scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) were used to characterize the hybrid composite made of Al-Cu-Mg alloy. The optical and SEM microstructural analyses demonstrated an even distribution of SiC and PSSA nanosize reinforcements within the matrix. The EDS analysis revealed SiC and PSSA reinforcement particles in the composite. The mechanical properties (tensile, flexural, and impact strength) and wear properties (wear rate and coefficient of friction) of the composites and alloys were evaluated according to the ASTM standards. The hybrid reinforced composites outperformed the base alloy. Among all composites, the 2:2 wt% SIC and PSSA hybrid-reinforced composites exhibited a significant enhancement in both tensile and flexural strength, with a 22.64% and 27.64% increase in strength, respectively. However, the inclusion of these reinforcements led to a reduction in the ductility and impact strength of the Al-Cu-Mg alloy composite. The 0:4 wt% SiC- and PSSA-reinforced composites experienced the largest reductions in ductility and impact strength, with decreases of 47.67% and 4.38%, respectively. For the 2:2 wt% SiC and PSSA composites, these reductions were 23.64% and 3.19%, respectively. The SEM analysis of the fractured surfaces of the composites tested for mechanical properties revealed evidence of both ductile and brittle fracture mechanisms in the tensile, flexural, and impact tests. The wear behaviour of the prepared samples was evaluated, and all composites exhibited superior performance compared with the base alloy, demonstrating adhesive and abrasive wear mechanisms and varying friction coefficients. Among all the composites, the 2:2 wt% SiC- and PSSA-reinforced composites exhibited high wear resistance and a lower coefficient of friction than the other fabricated composites.

Investigation on the effect of SiC and TiB2 ceramic particles on mechanical and tribological properties of Al7075 hybrid metal matrix composites prepared through conventional stir casting technique

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Tribological, mechanical and microstructure characteristics of hybrid aluminium matrix composite containing titanium carbide (TiC) and graphite particles

Mechanical Characteristics and Wear Behaviour of Al/SiC and Al/SiC/B4C Hybrid Metal Matrix Composites Fabricated Through Powder Metallurgy Route

Empirical investigation on controlled porosity level and dry sliding wear behavior of Al7075-(T6) doped with SiC+MoS2 based hybrid composites via advanced vacuum-assisted stir casting

Investigation of Mechanical and Tribological Properties of Al6061–TiB2 Metal Matrix Composites

Mechanical and wear analysis of AA6061-T6-SiC-TiC-graphite metal matrix composite

Effect of SiC Content on Mechanical and Tribological Properties of Al2024-SiC Composites

A Study On The Effects Of Hybrid (Sic- Pssa) Nano Sized Reinforcement On Mechanical And Tribological Behaviour Of Al Alloy-Based Metal Matrix Composite Produced By Ultrasonic Assisted Stir Casting

Effect of SiC Weight Percentage on Tribological Characteristics of Al7075/SiC Composites

Experimental Investigations on Microstructure, Mechanical and Wear Behavior Under Dry Sliding of Al6061 with Particulate-Reinforced SiC and TiB2 Metal Matrix Composite Developed by Stir Casting

Effects of Silicon Carbide and Tungsten Carbide in Aluminium Metal Matrix Composites

Influence of TiC Particles on Mechanical and Tribological Characteristics of Advanced Aluminium Matrix Composites Fabricated through Ultrasonic-Assisted Stir Casting

Mechanical and wear behavior of Al 7075/Al2O3/SiC/mg metal matrix nanocomposite by liquid state process

Influence of Silicon Carbide Reinforcements on Mechanical and Wear Behaviour AA7075/15% wt. Glass fiber Hybrid Composites

Dry Sliding Wear Studies on Sillimanite and B4C Reinforced Aluminium Hybrid Composites Fabricated by Vacuum Assisted Stir Casting Process

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Tribological and Structural Effects of Titanium Carbide and Hexagonal Boron Nitride Reinforcement on Aluminum Matrix Hybrid Composites

Fabrication and Mechanical Behaviour Investigation on Aluminium 7075 Boron Carbide and Inconel Alloy 625 Metal Matrix Composite Using Ultra Sonic Stir Casting Method

The effect of reinforcement particles weight percentage on the mechanical properties and plastic flow behaviour of aluminum alloy 7075 matrix material

Corrigendum: A study on the effects of hybrid (SIC- PSSA) nano sized reinforcement on mechanical and tribological behaviour of Al alloy-based metal matrix composite produced by ultrasonic assisted stir casting (2024 Mater. Res. Express 11 075010)