Abstract:Due to the high modulus, high strength, low density, excellent wear resistance and good neutron absorption, the boron carbide (B4C) particle reinforced aluminum (Al) matrix composites have been widely applied in the aerospace, weaponry, transportation and neutron shielding fields. In response to the increasing requirement of better strength -ductility matching of B4C/Al composites, introducing a nano-scale reinforcement into the B4C/Al composites becomes an attractive research focus. In this work, the SiC nanowires were ball-milled with Al powders, and then the SiC/Al composite powders were mixed with B4C microparticles. Thus, the 15vol. % B4C/SiC/Al composites with different volume fractions of SiC nanowires were fabricated by hot-pressing sintering and hot extrusion. B4C microparticles and SiC nanowires are uniformly dispersed in the B4C/SiC/Al composites, while the introduced SiC nanowires effectively decrease the Al matrix grain sizes. B4C/SiC/Al composites produce the better strength-ductility matching than that of B4C/Al composites, while the 15vol. % B4C/SiC/Al composite with 1vol. % SiC nanowires achieved the best strength-ductility matching. It generates the 281.7 ± 2.7 MPa in yield strength, 351.2 ± 0.1 MPa in ultimate tensile strength and 5.9 ± 0.7% in failure elongation, which are increased by 18.2%, 15.1% and 13.5% compared to the B4C/Al composites. Uniformly dispersed B4C microparticles and SiC nanowires largely block the dislocation motions and improve the dislocation storage capacity, which results in a more significant hetero-deformation induced (HDI) hardening effect in the B4C/SiC/Al composites. Moreover, the B4C/Al interfacial transition regions with the added SiC nanowires becomes stronger, which can enhance the load transfer efficiency of the B4C/Al interfaces as a result of the existing dislocation hardening zones. In conclusion, it is a good strategy to combine the synergistic strengthening effect of micro-scale and nano-scale reinforcements in the metal matrix composites.

Mechanical Characteristics and Wear Behaviour of Al/SiC and Al/SiC/B4C Hybrid Metal Matrix Composites Fabricated Through Powder Metallurgy Route

Effect of B4C and SiC nanoparticle reinforcement on the wear behavior and surface structure of aluminum (Al6063-T6) matrix composite

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Effects of Silicon Carbide and Tungsten Carbide in Aluminium Metal Matrix Composites

Micro-mechanical and tribological behavior of Al/SiC/B4C/CNT hybrid nanocomposite

Investigation on the effect of SiC and TiB2 ceramic particles on mechanical and tribological properties of Al7075 hybrid metal matrix composites prepared through conventional stir casting technique

Mechanical and wear analysis of AA6061-T6-SiC-TiC-graphite metal matrix composite

Fabrication, microstructure characterization and mechanical properties of B4C microparticles and SiC nanowires hybrid reinforced aluminum matrix composites

Investigating the Effect of Particle Sizes of SiC and Graphite on Strengthening of Aluminium Metal Matrix Composites

Microstructure and properties of aluminium matrix hybrid nanocomposite

Fabrication And Characterization of Al/ Sic/ Gr Hybrid Metal Matrix Composite Fabricated By Powder Metallurgy

Evaluation of Mechanical and Wear Properties of Al 5059/B4C/Al2O3 Hybrid Metal Matrix Composites

Investigation of Mechanical Properties of Aluminium 6061-Silicon Carbide, Boron Carbide Metal Matrix Composite

Mechanical and wear behavior of Al 7075/Al2O3/SiC/mg metal matrix nanocomposite by liquid state process

Analysis on Mechanical Behaviour of Binary and Hybrid Al2014 Metal Matrix Composites

Influence of Silicon Carbide Reinforcements on Mechanical and Wear Behaviour AA7075/15% wt. Glass fiber Hybrid Composites

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Influence of B4C on Dry Sliding Wear Behavior of B4C/Al–Mg–Si Composites Synthesized via Powder Metallurgy Route

Mechanical Properties of Aluminum-4043/Nickel-coated Silicon Carbide Composites Produced via Stir Casting

Mechanical and tribological properties of hybrid and monolithic reinforced hypoeutectic Al‐Si matrix composites

Effect of SiC Content on Mechanical and Tribological Properties of Al2024-SiC Composites