Abstract:The etching of high aspect ratio structures in silicon via the Bosch process is essential in modern technologies such as microelectromechanical systems (MEMS) and through‑silicon vias (TSV) fabrication. The process can be very demanding on the mask selectivity due to long etching times, and it has been shown that an Al2O3 hard mask is very suitable in this regard, as it offers significantly higher selectivity compared to the conventional SiO2 or resist masks. In this work, we employ a combination of Scanning Electron Microscopy (SEM), Spectroscopic Ellipsometry (SE) and X-Ray Photoelectron Spectroscopy (XPS) depth profiling to scrutinize the Al2O3 mask etching mechanism and therefore the origin of the extraordinary high selectivity. We demonstrate that by increasing the passivation step time, a thicker fluorocarbon polymer layer is formed on the Al2O3, and Al2O3 is then removed with a minuscule average etch rate of ~0.01 nm/min. XPS depth profiling reveals that during Deep Reactive Ion Etching (DRIE) using the Bosch process, an AlFx layer is formed between the polymer and Al2O3. As AlFx is non-volatile, it requires sputtering to be removed. If the polymer layer is thick enough to attenuate the incoming ions such that their energy is not sufficient to lead to desorption of AlFx, such as when using a longer passivation time, the mask is not eroded. By investigating the surface after different amounts of DRIE cycles, we also obtained information about the formation rate of AlFx and the changes in the Al2O3 and polymer thicknesses over the course of a DRIE process. These findings further expand the knowledge of DRIE and can help process engineers to tailor the processes accordingly.

Effects of mask material conductivity on lateral undercut etching in silicon nano-pillar fabrication

Graphene Masks As Passivation Layers in the Electrochemical Etching of Silicon

Investigation of Amorphous Silicon As Dry Etch Hard Mask in BEOL Low-k Dielectric Patterning

Temperature and oxygen concentration effects on anisotropy in chromium hard mask etching for nanoscale fabrication

Etch mechanism of an Al2O3 hard mask in the Bosch process

High Aspect Ratio Etching of Nanopores in PECVD SiC Through AAO Mask

Etching of high aspect ratio features in Si using SF6∕O2∕HBr and SF6∕O2∕Cl2 plasma

Molecular dynamics simulation of Si trench etching with SiO2 hard masks

Maskless Etching Of Three-Dimensional Silicon Structures In Koh

Etch Properties of Amorphous Carbon Material Using RF Pulsing in the O2/N2/CHF3 Plasma.

A spin-on photosensitive polymeric etch protection mask for anisotropic wet etching of silicon

Highly Selective Etch of Silicon Dioxide with Tungsten Hard Mask Deposited by PVD Process

Controllable Fabrication of Silicon Nanopore Arrays by Two-Step Inductively Coupled Plasma Etching Using Self-Assembled Anodic Aluminum Oxide Mask

Which Etchant Used and Whether an Etching Mask Exists: How They Make Differences on Convex-Corner Undercutting Configuration and Compensation Criteria

Wet Scandium Etching for hard mask formation on a silicon substrate

Fabrication of 10-nm Si pillars with self-formed etching masks

Low-temperature plasma etching of high aspect-ratio densely packed 15 to sub-10 nm silicon features derived from PS-PDMS block copolymer patterns

Wafer level bulk titanium ICP etching using SU8 as an etching mask

Evidence for faster etching at the mask-substrate interface: atomistic simulation of complex cavities at the micron-/submicron-scale by the continuous cellular automaton

Fabrication Of Silicon Cones And Pillars Using Rough Metal Films As Plasma Etching Masks

Morphology Improvement of SiC Trench by Inductively Coupled Plasma Etching Using Ni/Al 2 O 3 Bilayer Mask