Abstract:Wet anisotropic etching based silicon micromachining is an important technique to fabricate freestanding (e.g. cantilever) and fixed (e.g. cavity) structures on different orientation silicon wafers for various applications in microelectromechanical systems (MEMS). {111} planes are the slowest etch rate plane in all kinds of anisotropic etchants and therefore, a prolonged etching always leads to the appearance of {111} facets at the sidewalls of the fabricated structures. In wet anisotropic etching, undercutting occurs at the extruded corners and the curved edges of the mask patterns on the wafer surface. The rate of undercutting depends upon the type of etchant and the shape of mask edges and corners. Furthermore, the undercutting takes place at the straight edges if they do not contain {111} planes. {100} and {110} silicon wafers are most widely used in MEMS as well as microelectronics fabrication.This paper reviews the fabrication techniques of convex corner on {100} and {110} silicon wafers using anisotropic wet chemical etching. Fabrication methods are classified mainly into two major categories: corner compensation method and two-steps etching technique. In corner compensation method, extra mask pattern is added at the corner. Due to extra geometry, etching is delayed at the convex corner and hence the technique relies on time delayed etching. The shape and size of the compensating design strongly depends on the type of etchant, etching depth and the orientation of wafer surface. In this paper, various kinds of compensating designs published so far are discussed. Two-step etching method is employed for the fabrication of perfect convex corners. Since the perfectly sharp convex corner is formed by the intersection of {111} planes, each step of etching defines one of the facets of convex corners. In this method, two different ways are employed to perform the etching process and therefore can be subdivided into two parts. In one case, lithography step is performed after the first step of etching, while in the second case, all lithography steps are carried out before the etching process, but local oxidation of silicon (LOCOS) process is done after the first step of etching. The pros and cons of all techniques are discussed.

Which Etchant Used and Whether an Etching Mask Exists: How They Make Differences on Convex-Corner Undercutting Configuration and Compensation Criteria

Study on convex-corner undercutting formed by masked-maskless etching in aqueous KOH

Investigation of Amorphous Silicon As Dry Etch Hard Mask in BEOL Low-k Dielectric Patterning

A New Explanation of Mask-corner Undercut in Anisotropic Silicon Etching: Saddle Point in Etching Rate Diagram

Maskless Etching Of Three-Dimensional Silicon Structures In Koh

A Study On Etching Profiles Of Sacrificial Layers

A comprehensive review on convex and concave corners in silicon bulk micromachining based on anisotropic wet chemical etching

Study on maskless etching of silicon symmetric beam-mass structure in aqueous KOH

A New Approach To Convex Corner Compensation For Anisotropic Etching Of (100)Si In Koh

Effects of mask material conductivity on lateral undercut etching in silicon nano-pillar fabrication

Stress-Etching Using Laser Electrochemical Micromachining with Masks

A Novel Anisotropic Wet Etching Process of (100)-Silicon with Areaefficiency on Convex Corner Compensation Patterns

Toward Controllable Wet Etching of Monocrystalline Silicon: Roles of Mechanically Driven Defects

Convex corner undercutting of {100} silicon in anisotropic KOH etching: the new step-flow model of 3-D structuring and first simulation results

Shape Formation Analysis of Silicon Nanopore Fabricated by Anisotropic Wet Etching Method

An Etchant for Delineation of Flow Pattern Defects in Heavily Doped N-Type Silicon Wafers

Forming a Rounded Convex Corner by Using Two-Step Anisotropic KOH Wet Etching

Anisotropic etching of Si

A novel convex corner compensation for wet anisotropic etching on (100) silicon wafer

Modified Model for Sacrificial Layer Etching

Silicon (100) undercutting modelling and corner compensation structures design in wet anisotropic etching process