Abstract:So far, intrinsic hydrogenated amorphous silicon (a-Si:H(i)) has been commonly used below molybdenum oxide (MoOx) to form a good contact. An a-Si:H(i)/MoOx stack gives good surface passivation, but often results in poor carrier selectivity after exposure to slightly elevated temperatures >130 °C (Geissbühler et al., 2015) [1]. For this reason, we have investigated an alternative interface layer, a very thin Al2O3 tunneling layer (<2 nm), deposited by atomic layer deposition (ALD), that can provide surface passivation, higher transparency and thermal stability without affecting the hole transport across the contact. To demonstrate this new passivating contact a 6" moly-poly cell, with an Al2O3/MoOx stack at the front side and n-type doped polysilicon at the rear side, was made using a high- throughput spatial ALD tool, and E-beam PVD, for the Al2O3 and MoOx layers, respectively. This resulted in an efficiency of 18.2% with a Voc of 651 mV, a FF of 75.6% and a Jsc of 36.9 mA/cm2. A post-deposition anneal (PDA) of the thin Al2O3 interlayer has significant effect on the Al2O3 thickness, layer stoichiometry, contact selectivity, and sputtering-induced damage. Annealing at higher TPDA (350–600 °C) results in ineffective hole carrier transport and makes the stack more sensitive to ITO damage. The best performing device was, therefore, made using an Al2O3 layer without a PDA treatment. Moreover, we have found that this solar cell structure is thermally stable up to at least 210 °C, and even slightly improves under annealing which makes this device industrially appealing.

Aluminum Oxide Passivating Tunneling Interlayers for Molybdenum Oxide Hole-Selective Contacts

Investigation in Feasibility of Molybdenum As A Back Contact Layer for Silicon Based Quantum Dot Solar Cells

Thermally stable MoOx hole selective contact with Al2O3 interlayer for industrial size silicon solar cells

Pre-deposition Growth of Interfacial SiO2 Layer by Low-Oxygen-partial-pressure Oxidation in the Al2O3/4H-SiC MOS Structure

Solution-processed molybdenum oxide films by low-temperature annealing for improved silicon surface passivation

Atomic-Layer-Deposited H:MoO x Function Layer as Efficient Hole Selective Passivating Contact in Silicon Solar Cells

A Study of Contact Properties Between Molybdenum and Amorphous Silicon Tin Oxide Thin Film Transistors

MoOx Hole Collection Layer for A-Si: H Based Photovoltaic Cells

Interface study of molybdenum oxide thin films on n- and p-type crystalline silicon surface

Aluminum oxide as a dielectric and passivation layer for (flexible) metal-oxide and 2D semiconductor devices

UV-Ozone Oxide layer for Junction Passivation and Passivating Contact Process of Silicon Solar Cells

Low-resistivity Ohmic contacts of Ti/Al on few-layered 1T'-MoTe2/2H-MoTe2 heterojunctions grown by chemical vapor deposition

Aluminum oxide layers as possible components for layered tunnel barriers

Titanium Contacts to MoS2 with Interfacial Oxide: Interface Chemistry and Thermal Transport

Spatial Atomic Layer Deposition of Molybdenum Oxide for Industrial Solar Cells

Novel interlayer boosting the performance of evaporated Cu2O hole‐selective contacts in Si solar cells

Temperature-induced stoichiometric changes in thermally grown interfacial oxide in tunnel-oxide passivating contacts

Contact-induced doping in aluminum-contacted molybdenum disulfide

Atomic Layer Deposition of Ultrathin La2O3/Al2O3 Nanolaminates on MoS2 with Ultraviolet Ozone Treatment

Surface transfer doping of MoO3 on hydrogen terminated diamond with an Al2O3 interfacial layer

Direct atomic layer deposition of ultrathin aluminium oxide on monolayer $MoS_2$ exfoliated on gold: the role of the substrate