Abstract:Forming limit diagrams (FLDs) are very important in predicting the behavior of the sheet. Therefore, predicting and drawing these diagrams by theoretical and experimental methods has been one of the main objectives of this paper. In this paper, the formability behavior of 5083 aluminum sheet was investigated by considering the strain hardening behavior. Tensile tests has performed in seven directions 0°, 15°, 30°, 45°, 60°, 75° and 90° from the rolling direction due to identify and calibrate coefficients of BBC2008 advanced yield criteria. The yield stresses was defined in the plane strain mode, also the anisotropy coefficients and the appropriate error function were extracted and then the relationships of the plane strain yield stress were added to the error function. The error function was optimized using Genetic Algorithm and limit strains were calculated using yield coefficients. The results showed that if the strain hardening exponent increases by 0.1, the limit strains increase by 30 to 40%. Also the results showed that the initial imperfection factor ( 𝑓 0 ) has a great effect on determining the FLD and with a very small change, it has a great effect on the FLD; So that by increasing this factor to about 0.016, the values of the limit strains are almost doubled. Using the results of this paper and having sheet properties such as yield strengths and anisotropy coefficients and proper selection of yield criteria, the FLD of different sheets to be theoretically determined with acceptable accuracy. [1] Plastic Instability and Fracture in Sheet Stretched over Rigid Punches. [2] Application of strain analysis to sheet metal forming problems in the press shop. [3] On discontinuous plastic states, with special reference to localized necking in thin sheets. [4] Limit strains in the processes of stretch-forming sheet metal. [5] The influence of strain-path changes on forming limit diagrams of A1 6111 T4. [6] Investigation of formability of low carbon steel sheets by forming limit diagrams. [7] Theoretical determination of forming limit diagram for steel, brass and aluminum alloy sheets. [8] Experimental and numerical evaluation of forming limit diagram for Ti6Al4V titanium and Al6061-T6 aluminum alloys sheets. [9] Experimental and numerical analysis of forming limit diagram (FLD) and forming limit stress diagram (FLSD). [10] Forming limit and fracture mechanism of ferritic stainless steel sheets. [11] Calculation of forming limit diagrams using Hill's 1993 yield criterion. [12] The effects of anisotropic yield functions and their material parameters on prediction of forming limit diagrams. [13] The Effect of Advanced BBC2003, Yld2004 and BBC2008 Yield Criteria on FLDs Based on MK, Swift's and Hill's Models. [14] An experimental and theoretical investigation for determination of yield criteria parameters... [15] The forming limit curve for multiphase advanced high strength steels... [16] Forming limits of dual phase steels using crystal plasticity in conjunction with MK approach. [17] Prediction of FLD for sheet metal by considering through-thickness shear stresses. [18] Investigation on the effective range of the through thickness shear stress... [19] Controlling factors of forming limit curve: A review. [20] Crystal plasticity finite element – Marciniak-Kuczynski approach with surface roughening effect... [21] Plane stress yield criterion for highly anisotropicsheet metals. [22] Techniques of measurement of body composition Part II. [23] An improved analytical description of orthotropy in metallic sheets. [24] A study of microstructure and tribological properties of Al 5083 MMC processed by direct extrusion. [25] A novel and simple method for the measurement of plane strain work hardening.

Effect of plastic anisotropy on ironing formability of 3104 aluminum alloy hard sheets

Study of the deep drawing behavior and crystallographic texture of AA 3104-H19 aluminum alloy sheets

Effect of plastic anisotropy on notch deformation behavior of 7075 high-strength aluminum alloy sheet subjected to axial tension

Formability Window of Aluminium Alloy Sheet at Variable Blank-Holder Force

Anisotropic Behavior in Plasticity and Ductile Fracture of an Aluminum Alloy

Ductile Fracture Initiation of Anisotropic Metal Sheets

Friction Anisotropy of Aluminum 6111-T4 Sheet with Flat and Laser-Textured D2 Tooling

Effect of Initial Orientation on the Anisotropy in Microstructure and Mechanical Properties of 2195 Al-Li Alloy Sheet during Hot Tensile Deformation

Effect of Microstructures on the Anisotropy of the Roll Casting Strip of Cold Rolled 3003 Aluminum Alloy

Strain Rate Effect on the Fracture Behavior of the AA5754 Aluminum Alloy

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

Effect of Softening on the Mechanical Properties and Formability of Ribbon from Alloy 3104

Investigation of the Flange Earring of Deep-Drawing Aluminum Sheets by Rate-Independent Polycrystalline Plasticity Finite Element Analysis

Experimental and Theoretical Study of Formability Behavior of Aluminum Alloy 5083 Sheet for Determination of Advanced Anisotropic Yield Criteria Coefficient and Prediction of Forming Limit Diagram

Earing Prediction of AA5754-H111 (Al-Alloy) with Linear Transformation-Based Anisotropic Drucker Yield Function under Non-Associated Flow Rule (Non-AFR)

Testing and Modeling the Effect of Strain-Rate on Plastic Anisotropy for A Traditional High Strength Steel

Effects of Anisotropic Yield Criteria on the Prediction of Sheet Metal Forming of Aluminum Alloy Sheet

Finite Element Modeling for Deep-Drawing of Aluminum Alloy Sheet 6014-T4 Using Anisotropic Yield and Non-Afr Models

Study on the Effect of Anisotropy on Plastic Flow Localization of Third Generation Advanced High Strength Steel

Anisotropic Plasticity Behavior of Rolled 316L Ultra-Thin Sheet and Its Application to Micro-Deep Drawing Modeling

Anisotropic Behavior of As-Extruded 7003 Aluminum Alloy under Quasi-Static Compression and High-Speed Impact