Abstract:Sheet metals usually exhibit a certain degree of plastic anisotropy because of the rolling effect. To characterize the anisotropic behavior in simulations related to large deformation, strain-rate independent phenomenological models are frequently used in quasi-static conditions. Two functions are generally included in such a model, i.e. the yield function and the plastic potential. The former limits the stress state within the yield surface while the latter determines the direction of the plastic strain increment. Traditional plasticity models mostly assume associated flow rule, in which the two functions mentioned above are identical. With the enhanced demand of accuracy, the forms of the associated models become too complex with more and more parameters to achieve an easy calibration procedure. Alternatively, in the past decade the non-associated models were increasingly used for sheet metals. Separate functions for the two aspects of plasticity lead to efficient characterization and convenient calibration. In numerical study of dynamic loading cases, how to characterize strain-rate dependence of plasticity is an important issue. Some visco-plastic models were developed to take the rate effect into account, e.g. Johnson-Cook and Cowper-Symonds models, where the isotropic J2 flow theory was commonly used. However, when the material is severely anisotropic, this approach is very likely to be insufficient, and a model including both anisotropy and rate dependence would be needed. Extending a non-associated anisotropic model to be rate-dependent is a promising approach which has not been published in open literature to the best knowledge of the authors. Objective of the present study is to develop an applicable model for characterizing dynamic mechanical behavior of a typical high-strength steel sheet. Two steps are performed. The material is investigated under quasi-static loading firstly. Tensile test results show an obvious anisotropy which cannot be described by traditional associated models. So the non-associated Hill48 model is chosen and calibrated. Accuracy of the model is verified by a quasi-static punching test. Thereafter the dynamic material properties are obtained by conducting tensile tests at quite a few strain-rate levels covering 0.0004–1200s−1. To characterize the positive strain-rate effect in strength, the non-associated Hill48 model is extended to be visco-plastic after checking two rate-dependence formulations in existing isotropic models. With implementing the extended model into a user subroutine of ABAQUS/explicit, simulations of the dynamic tension tests are run and compared to the real experiments. A good agreement between the simulated and the experimental result is achieved using the VUMAT.

Characterisation of the plane anisotropy and its effect on interstitial free steel thin sheet metal forming simulation

Modelling the anisotropy evolution in sheet metals with heterogeneous properties

Multiaxial constitutive behavior of an interstitial-free steel: Measurements through X-ray and digital image correlation

An innovation in finite element simulation via crystal plasticity assessment of grain morphology effect on sheet metal formability

Study on the Effect of Anisotropy on Plastic Flow Localization of Third Generation Advanced High Strength Steel

A non-associated anisotropic plasticity model with mixed isotropic–kinematic hardening for finite element simulation of incremental sheet metal forming process

A Physical-Based Plane Stress Constitutive Model for High Strength AA7075 under Hot Forming Conditions

Anisotropic Plasticity Behavior of Rolled 316L Ultra-Thin Sheet and Its Application to Micro-Deep Drawing Modeling

Characterization of the Microstructure Evolution in IF-Steel and AA6016 during Plane-Strain Tension and Simple Shear

Non-associated and Non-quadratic Characteristics in Plastic Anisotropy of Automotive Lightweight Sheet Metals

Annealing behaviour and mechanical properties of severely deformed interstitial free steel

The effect of heat treatment on anisotropy behavior and formability of three-layer composite sheets using digital image correlation method

An Experimental Methodology to Characterize the Plasticity of Sheet Metals from Uniaxial to Plane Strain Tension

Characterization and constitutive analysis-based crystal plasticity of warm flow and fracture behaviours of 2060 Al-Cu-Li alloy

Finite strain anisotropic elasto-plastic model for the simulation of the forming and testing of metal/short fiber reinforced polymer clinch joints at room temperature

Extension of Non-Associated Hill48 Model for Characterizing Dynamic Mechanical Behavior of A Typical High-Strength Steel Sheet

Heterogeneous local plastic deformation of interstitial free steel revealed using in-situ tensile testing and high angular resolution electron backscatter diffraction

Non-associated anisotropic plasticity of metal sheets based on the distortional concept

Orientation dependence of dynamic compared to static recovery in Interstitial Free steel

Development of a plane strain tensile test to characterize the formability of 5xxx and 6xxx aluminium alloys

Extensive anisotropic lath martensite plasticity in dual-phase steels: A numerical-experimental investigation