Abstract:Sheet metals usually exhibit a certain degree of plastic anisotropy because of the rolling effect. To characterize the anisotropic behavior in simulations related to large deformation, strain-rate independent phenomenological models are frequently used in quasi-static conditions. Two functions are generally included in such a model, i.e. the yield function and the plastic potential. The former limits the stress state within the yield surface while the latter determines the direction of the plastic strain increment. Traditional plasticity models mostly assume associated flow rule, in which the two functions mentioned above are identical. With the enhanced demand of accuracy, the forms of the associated models become too complex with more and more parameters to achieve an easy calibration procedure. Alternatively, in the past decade the non-associated models were increasingly used for sheet metals. Separate functions for the two aspects of plasticity lead to efficient characterization and convenient calibration. In numerical study of dynamic loading cases, how to characterize strain-rate dependence of plasticity is an important issue. Some visco-plastic models were developed to take the rate effect into account, e.g. Johnson-Cook and Cowper-Symonds models, where the isotropic J2 flow theory was commonly used. However, when the material is severely anisotropic, this approach is very likely to be insufficient, and a model including both anisotropy and rate dependence would be needed. Extending a non-associated anisotropic model to be rate-dependent is a promising approach which has not been published in open literature to the best knowledge of the authors. Objective of the present study is to develop an applicable model for characterizing dynamic mechanical behavior of a typical high-strength steel sheet. Two steps are performed. The material is investigated under quasi-static loading firstly. Tensile test results show an obvious anisotropy which cannot be described by traditional associated models. So the non-associated Hill48 model is chosen and calibrated. Accuracy of the model is verified by a quasi-static punching test. Thereafter the dynamic material properties are obtained by conducting tensile tests at quite a few strain-rate levels covering 0.0004–1200s−1. To characterize the positive strain-rate effect in strength, the non-associated Hill48 model is extended to be visco-plastic after checking two rate-dependence formulations in existing isotropic models. With implementing the extended model into a user subroutine of ABAQUS/explicit, simulations of the dynamic tension tests are run and compared to the real experiments. A good agreement between the simulated and the experimental result is achieved using the VUMAT.

A non-associated anisotropic plasticity model with mixed isotropic–kinematic hardening for finite element simulation of incremental sheet metal forming process

A Rate-Independent Non-Associated Constitutive Model for Finite Element Simulation of Sheet Metal Forming

Evaluation of Associated and Non-Associated Flow Metal Plasticity; Application for Dc06 Deep Drawing Steel

Non-associated anisotropic plasticity of metal sheets based on the distortional concept

Application of the Finite Element Method to the Incremental Forming of Polymer Sheets: The Thermomechanical Coupled Model and Experimental Validations

Constitutive modeling based on non-associated flow rule for anisotropic sheet metals forming

Evaluation of Anisotropic Constitutive Models: Mixed Anisotropic Hardening and Non-Associated Flow Rule Approach

Research on incremental forming simulation based on an improved constitutive model

An Evolutionary Anisotropic Model for Sheet Metals Based on Non-Associated Flow Rule Approach

Anisotropic ductile damage fully coupled with anisotropic plastic flow: Modeling, experimental validation, and application to metal forming simulation

Extension of Non-Associated Hill48 Model for Characterizing Dynamic Mechanical Behavior of A Typical High-Strength Steel Sheet

An efficient multiphysics solid shell based finite element approach for modeling thin sheet metal forming processes

Numerical Modelling for Efficient Analysis of Large Size Multi-Stage Incremental Sheet Forming

Modelling the anisotropy evolution in sheet metals with heterogeneous properties

A non-quadratic pressure-sensitive constitutive model under non-associated flow rule with anisotropic hardening: Modeling and validation

Springback investigation of anisotropic aluminum alloy sheet with a mixed hardening rule and Barlat yield criteria in sheet metal forming

A Dislocation Density Based Crystal Plasticity Model of 3D Complex Sheet Metal Forming

Non-Associated Flow Rule Constitutive Modeling Considering Anisotropic Hardening for the Forming Analysis of Orthotropic Sheet Metal

Analytical Modeling of Fracture Strain and Experimental Validation in Incremental Sheet Forming

Analytical Modeling and Experimental Validation of the Forming Force in Several Typical Incremental Sheet Forming Processes

Simulation Of Sheet Metal Forming Processes Using A Fully Rheological-Damage Constitutive Model Coupling And A Specific 3d Remeshing Method