Abstract:Sheet metals usually exhibit a certain degree of plastic anisotropy because of the rolling effect. To characterize the anisotropic behavior in simulations related to large deformation, strain-rate independent phenomenological models are frequently used in quasi-static conditions. Two functions are generally included in such a model, i.e. the yield function and the plastic potential. The former limits the stress state within the yield surface while the latter determines the direction of the plastic strain increment. Traditional plasticity models mostly assume associated flow rule, in which the two functions mentioned above are identical. With the enhanced demand of accuracy, the forms of the associated models become too complex with more and more parameters to achieve an easy calibration procedure. Alternatively, in the past decade the non-associated models were increasingly used for sheet metals. Separate functions for the two aspects of plasticity lead to efficient characterization and convenient calibration. In numerical study of dynamic loading cases, how to characterize strain-rate dependence of plasticity is an important issue. Some visco-plastic models were developed to take the rate effect into account, e.g. Johnson-Cook and Cowper-Symonds models, where the isotropic J2 flow theory was commonly used. However, when the material is severely anisotropic, this approach is very likely to be insufficient, and a model including both anisotropy and rate dependence would be needed. Extending a non-associated anisotropic model to be rate-dependent is a promising approach which has not been published in open literature to the best knowledge of the authors. Objective of the present study is to develop an applicable model for characterizing dynamic mechanical behavior of a typical high-strength steel sheet. Two steps are performed. The material is investigated under quasi-static loading firstly. Tensile test results show an obvious anisotropy which cannot be described by traditional associated models. So the non-associated Hill48 model is chosen and calibrated. Accuracy of the model is verified by a quasi-static punching test. Thereafter the dynamic material properties are obtained by conducting tensile tests at quite a few strain-rate levels covering 0.0004–1200s−1. To characterize the positive strain-rate effect in strength, the non-associated Hill48 model is extended to be visco-plastic after checking two rate-dependence formulations in existing isotropic models. With implementing the extended model into a user subroutine of ABAQUS/explicit, simulations of the dynamic tension tests are run and compared to the real experiments. A good agreement between the simulated and the experimental result is achieved using the VUMAT.

Plastic Anisotropy Constitutive Equation of Sheet Metal and Its Stamping Process Simulation

Multi-scale Modelling of Evolving Plastic Anisotropy During Al-alloy Sheet Forming

Application of anisotropic constitutive equations to numerical simulation of sheet forming

Constitutive modeling based on non-associated flow rule for anisotropic sheet metals forming

Numerical Simulation on Sheet Metal Forming with Rate-Independent Polycrystalline Plasticity Fem

Effects of Anisotropic Yield Criteria on the Prediction of Sheet Metal Forming of Aluminum Alloy Sheet

An Experimental and Theoretical Study on Constitutive Model of Al-2024T4 for Sheet Metal Incremental Forming

An Interpolation Type Anisotropic Yield Function and Its Application in Sheet Metal Forming Simulation

Extension of Non-Associated Hill48 Model for Characterizing Dynamic Mechanical Behavior of A Typical High-Strength Steel Sheet

Non-associated anisotropic plasticity of metal sheets based on the distortional concept

A Homogenized Anisotropic Constitutive Model of Perforated Sheets for Numerical Simulation of Stamping

Computer simulation of sheet metal forming processes using crystalline plasticity

Experimental and Modeling Investigation on Anisotropic Plastic Flow of Metal Plates under Nonproportional Loading Conditions

An Identification Method for Anisotropic Plastic Constitutive Parameters of Sheet Metals

Evaluation of Associated and Non-Associated Flow Metal Plasticity; Application for Dc06 Deep Drawing Steel

Flange earing and its control on deep-drawing of anisotropy circular sheets

An Evolutionary Anisotropic Model for Sheet Metals Based on Non-Associated Flow Rule Approach

A Dislocation Density Based Crystal Plasticity Model of 3D Complex Sheet Metal Forming

Numerical Simulation of Sheet Metal Blanking Based on Fully Coupled Elastoplasticity-Damage Constitutive Equations Accounting for Yield Surface Distortion-Induced Anisotropy

Explicit Analysis of Transversely Anisotropic and Axisymmetric Sheet Metal Forming Process Using 6- Component Barlat Yield Function

3D Dynamic Simulation of Sheet Forming Process and Optimization of Process Parameters