Abstract:Forming limit diagrams (FLDs) are very important in predicting the behavior of the sheet. Therefore, predicting and drawing these diagrams by theoretical and experimental methods has been one of the main objectives of this paper. In this paper, the formability behavior of 5083 aluminum sheet was investigated by considering the strain hardening behavior. Tensile tests has performed in seven directions 0°, 15°, 30°, 45°, 60°, 75° and 90° from the rolling direction due to identify and calibrate coefficients of BBC2008 advanced yield criteria. The yield stresses was defined in the plane strain mode, also the anisotropy coefficients and the appropriate error function were extracted and then the relationships of the plane strain yield stress were added to the error function. The error function was optimized using Genetic Algorithm and limit strains were calculated using yield coefficients. The results showed that if the strain hardening exponent increases by 0.1, the limit strains increase by 30 to 40%. Also the results showed that the initial imperfection factor ( 𝑓 0 ) has a great effect on determining the FLD and with a very small change, it has a great effect on the FLD; So that by increasing this factor to about 0.016, the values of the limit strains are almost doubled. Using the results of this paper and having sheet properties such as yield strengths and anisotropy coefficients and proper selection of yield criteria, the FLD of different sheets to be theoretically determined with acceptable accuracy. [1] Plastic Instability and Fracture in Sheet Stretched over Rigid Punches. [2] Application of strain analysis to sheet metal forming problems in the press shop. [3] On discontinuous plastic states, with special reference to localized necking in thin sheets. [4] Limit strains in the processes of stretch-forming sheet metal. [5] The influence of strain-path changes on forming limit diagrams of A1 6111 T4. [6] Investigation of formability of low carbon steel sheets by forming limit diagrams. [7] Theoretical determination of forming limit diagram for steel, brass and aluminum alloy sheets. [8] Experimental and numerical evaluation of forming limit diagram for Ti6Al4V titanium and Al6061-T6 aluminum alloys sheets. [9] Experimental and numerical analysis of forming limit diagram (FLD) and forming limit stress diagram (FLSD). [10] Forming limit and fracture mechanism of ferritic stainless steel sheets. [11] Calculation of forming limit diagrams using Hill's 1993 yield criterion. [12] The effects of anisotropic yield functions and their material parameters on prediction of forming limit diagrams. [13] The Effect of Advanced BBC2003, Yld2004 and BBC2008 Yield Criteria on FLDs Based on MK, Swift's and Hill's Models. [14] An experimental and theoretical investigation for determination of yield criteria parameters... [15] The forming limit curve for multiphase advanced high strength steels... [16] Forming limits of dual phase steels using crystal plasticity in conjunction with MK approach. [17] Prediction of FLD for sheet metal by considering through-thickness shear stresses. [18] Investigation on the effective range of the through thickness shear stress... [19] Controlling factors of forming limit curve: A review. [20] Crystal plasticity finite element – Marciniak-Kuczynski approach with surface roughening effect... [21] Plane stress yield criterion for highly anisotropicsheet metals. [22] Techniques of measurement of body composition Part II. [23] An improved analytical description of orthotropy in metallic sheets. [24] A study of microstructure and tribological properties of Al 5083 MMC processed by direct extrusion. [25] A novel and simple method for the measurement of plane strain work hardening.

Anisotropic behaviour law for sheets used in stamping: A comparative study of steel and aluminium

Study on Simulation of Stamping Forming and Die Surface Optimization of Aluminum Alloy Plate

Effects of Anisotropic Yield Criteria on the Prediction of Sheet Metal Forming of Aluminum Alloy Sheet

Plastic Anisotropy Constitutive Equation of Sheet Metal and Its Stamping Process Simulation

Modeling material behavior of AA5083 aluminum alloy sheet using biaxial tensile tests and its application in numerical simulation of deep drawing

Influence of Material Models on the Accuracy of the Sheet Forming Simulation

Finite Element Modeling for Deep-Drawing of Aluminum Alloy Sheet 6014-T4 Using Anisotropic Yield and Non-Afr Models

Investigation of Anisotropy Effects on Sheet-Bulk Forming of Duplex Gear Parts

Anisotropic Fracture of Advanced High Strength Steel Sheets: Experiment and Theory

Consideration of Strength Differential Effect in Sheet Metals with Symmetric Yield Functions

Experimental and Theoretical Study of Formability Behavior of Aluminum Alloy 5083 Sheet for Determination of Advanced Anisotropic Yield Criteria Coefficient and Prediction of Forming Limit Diagram

Springback investigation of anisotropic aluminum alloy sheet with a mixed hardening rule and Barlat yield criteria in sheet metal forming

Analysis of Sheet Metal Forming (Stamping Process): A Study of the Variable Friction Coefficient on 5052 Aluminum Alloy

Characterisation of the plane anisotropy and its effect on interstitial free steel thin sheet metal forming simulation

Stepwise modelling method for post necking characterisation of anisotropic sheet metal

A Study on Yield Criteria Influence on Anisotropic Behavior and Fracture Prediction in Deep Drawing SECC Steel Cylindrical Cups

Extension of Non-Associated Hill48 Model for Characterizing Dynamic Mechanical Behavior of A Typical High-Strength Steel Sheet

Theoretical and Numerical Investigation of the Limit Strain of a 5754-O Aluminum Alloy Sheet Considering the Influence of the Hardening Law

Improving the Accuracy of Stamping Analyses Including Springback Deformations

Modeling stress anisotropy, strength differential, and anisotropic hardening by coupling quadratic and stress-invariant-based yield functions under non-associated flow rule

Effects of anisotropic yield criteria on the prediction of wrinkle during the deep-drawing forming of aluminum alloy sheet