Abstract:The aerospace industry uses a variety of materials in different forms like sheets, forgings, extruded rods, welded components and machined components for launch vehicle and satellite applications. As lighter and stronger materials are the aims of the aerospace industry, aluminium alloys are the most widely used materials in the in the aircraft and aerospace industries. These aluminum alloys used in the aerospace industry are subjected to a variety of processing operations, either in the sheet form after rolling, forging, heat treatment and machining conditions, to realize the final product implies that these alloys exhibit a wide range of properties depending on the processing conditions. Texture formation in a material takes place during its various processing stages. The actual orientation distribution in a poly crystal is the result of the manufacturing processes applied. In this context, it is important to characterize the evolution of texture, both macro and micro texture, in AA7075 and AFNOR7020 alloys, which are two of the important high strength aluminum alloys used in the Aerospace industry. This paper deals with the results of the crystallographic texture measurements carried out on the cold rolled and artificially aged AA7075 and AFNOR7020 aluminium alloys. Results obtained from the pole figure analysis, Orientation Distribution Function (ODF) method and estimation of the various fibres present in the cold rolled material and the volume fraction of the texture components are discussed in detail for the alloy. Results of the micro texture measurements using the EBSD are presented, explained and analyzed in detail. A comparison of the inverse pole figures (IPFs), Image Quality (IQ) maps, Misorientation angle, Grain Orientation Spread (GOS), Kernal Average Misorientation (KAM), CSL boundaries, Grain size and Grain boundary character distribution (GBCD) for materials cold rolled to different reduction for the alloy are done and analyzed. Conclusions are drawn regarding the evolution of texture from the above analysis. Deformation texture components Cu, Bs and S increase from the starting material as the rolling percentage increases. On the other hand, recrystallization texture components of Goss and Cube are observed to be weak. AFNOR7020 Alloy developed a stronger texture compared to the AA7075 alloy. S component of texture is stronger in AA7075 alloy whereas the Bs component is stronger in AFNOR7020 alloy. This is attributed to the shear banding which was found absent in the other alloy.

Study of the deep drawing behavior and crystallographic texture of AA 3104-H19 aluminum alloy sheets

Deformation-texture evolution in deep drawing of cold-rolled 3104 aluminum alloy sheet

Tensile Properties and Fractography of Three AA 2000 Series Aluminum Alloys Used for Aerospace Applications

Multi-scale numerical investigation of deep drawing of 6K21 aluminum alloy by crystal plasticity and a stress-invariant based anisotropic yield function under non-associated flow rule

In Fl Uence of Texture and Grain Re Fi Nement on the Mechanical Behavior of AA 2219 Fabricated by High Shear Solid State Material Deposition

Deformation and Recrystallization Textures in Straight-Rolled and Pseudo Cross-Rolled AA 3105 Aluminum Alloy

Study on microstructure, mechanical properties, and texture of the CC AA 3105 aluminum alloy processed by high-pressure heat treatment

Effect of Microstructures on the Anisotropy of the Roll Casting Strip of Cold Rolled 3003 Aluminum Alloy

Structural Characterization of the Rolled and Annealed 7475 Aluminum Alloy

Effect of plastic anisotropy on ironing formability of 3104 aluminum alloy hard sheets

Mechanical Properties and Microstructural Evolution of 6082 Aluminum Alloy with Different Heat Treatment Methods

On the Work-Hardening of AA 3104-H19 Aluminum Alloy

Modeling material behavior of AA5083 aluminum alloy sheet using biaxial tensile tests and its application in numerical simulation of deep drawing

Anisotropic Tensile Behavior and Related Yield Point Phenomena in Annealed Ultrafine-Grained Pure Aluminum

Deep Drawability of Al-Mg Alloys Produced by Twin Roll Continuous Casting Method: Investigation of Microstructure and Mechanical Properties

Evolution of Crystallographic Texture in Cold Rolled Al-Zn-Mg Alloys Used in Space Applications

Strain inhomogeneity and grain refinement in AA6063 aluminum alloy subjected to repetitive corrugation and straightening: comparison of experimental and finite element analysis

A Comparison Study Of Microstructure, Texture And Mechanical Properties Between Two 6xxx Aluminum Alloys

Influence of alloy chemistry on the deformation behaviour and anisotropic properties of aluminium ultra-fine-grained thin sheets

Effects of Grain Shape and Texture on the Through-Thickness Yield Strength of AA 7055 Aluminum Alloy Plate

Influence of different rolling processes on the microstructures and mechanical properties of 6016 aluminum alloy