Abstract:The constitutive behavior of AA7075 aluminum sheet like other metallic sheet materials is highly temperature and strain rate dependent at elevated temperatures. The uniaxial tensile test is commonly employed to characterize the temperature and strain rate dependent deformation behavior. However, the traditional uniaxial tensile testing and data analysis procedure treats the gauge length of sample as a uniformly-deforming (or homogeneous) region. This may not be accurate due to early localized deformation that is initiated in the gauge region at elevated temperatures. Treating the post-necking hardening behavior of uniaxial tensile samples has been an important task to expand the effective range of true stress-true strain curves at elevated temperatures for metal and alloys. To explore this issue, uniaxial tensile tests on AA7075-F sheets (with as-fabricated temper) were conducted at 673o K and four different test speeds. The test procedure also utilized an on-line 2-D digital image correlation (DIC) system method to obtain full-field strain map from the deforming gauge region of the test specimen. Local stress-strain curves at different points along the gauge length were then calculated based on the recorded local in-plane principal stress and strain values from macroscopic force data and current cross-section of the specimen at the chosen points. In this manner, the DIC strain analysis not only enabled the determination of stress-strain response but also the determination of strain rates at specific chosen points along the gauge length. The local stress-strain curves revealed significant deviation at an earlier stage of deformation from the global (or macroscopic) stress-strain response based on the entire gauge region. To estimate the constitutive behavior at different strain rates, a correction method to traditional stress-strain curves was applied to obtain a family of stress-strain curves at different constant strain rates based on the local stress-strain curves. Additionally, the material deformation response in the stress, strain and strain rate space in the 3D Cartesian coordinate system was also constructed for tests conducted at different stretching speeds. Further, a verification test was conducted to see if the above methodology could provide an accurate estimation of local deformation behavior of AA7075 sheet. Furthermore, the above experimental method was also coupled with the Gurson-Tvergarrd-Needleman (GTN) ductile void damage model and incorporated into ABAQUS-Explicit general purpose finite element (FE) analysis code via a VUMAT material subroutine. Good agreement was obtained for both the local and global stress-strain curves between the FE test simulation and experimental stress-strain results. The proposed experimental methodology and the resulting stress-strain-strain rate behavior is believed to be applicable in describing the strain rate-dependent constitutive behavior of AA7075-F sheet metals at 673o K.

On the Work-Hardening of AA 3104-H19 Aluminum Alloy

Theoretical and Numerical Investigation of the Limit Strain of a 5754-O Aluminum Alloy Sheet Considering the Influence of the Hardening Law

Strain Hardening under Large Deformation for AA5182

Characterization of Anisotropic Hardening of AA3003-O

Prediction of limit strains in hot forming of aluminium alloy sheets

Modeling material behavior of AA5083 aluminum alloy sheet using biaxial tensile tests and its application in numerical simulation of deep drawing

Study of the deep drawing behavior and crystallographic texture of AA 3104-H19 aluminum alloy sheets

Local and global tensile deformation behavior of AA7075 sheet material at 673K and different strain rates

Analysis of hot Formability of Al-4.6Mg-0.6Mn Alloy (AA5083)

Strain hardening and orientation hardening/softening in cold rolled AA 5052 aluminum alloy

Material modeling of 6016-O and 6016-T4 aluminum alloy sheets and application to hole expansion forming simulation

Local and global tensile deformation behavior of AA7075 sheet material at 673oK and different strain rates

Characterization on the thermal anisotropic behaviors of high strength AA7075 alloy with the Yld2004-18p yield function

Modeling of constitutive behavior and ductile fracture of AA5A06 aluminum alloy sheet in warm hydroforming process

Research and Revise on Constitutive Equation of 7050-T7451 Aluminum Alloy in High Strain Rate and High Temperature Condition

Flow stress and work hardening behaviour of Mg-3Al-1Zn alloy

Strain Hardening of 1565ch, AMg6, 01570, and 1580 Aluminum Alloys in the Process of Cold Rolling of Plates

Anisotropic Tensile Behavior and Related Yield Point Phenomena in Annealed Ultrafine-Grained Pure Aluminum

Cyclic Hardening Behavior of Roller Hemming in the Case of Aluminum Alloy Sheets

A Physically-Based Constitutive Modelling of a High Strength Aluminum Alloy at Hot Working Conditions

Prediction of the Work-Hardening Exponent for 3104 Aluminum Sheets with Different Grain Sizes