Abstract:The constitutive behavior of AA7075 aluminum sheet like other metallic sheet materials is highly temperature and strain rate dependent at elevated temperatures. The uniaxial tensile test is commonly employed to characterize the temperature and strain rate dependent deformation behavior. However, the traditional uniaxial tensile testing and data analysis procedure treats the gauge length of sample as a uniformly-deforming (or homogeneous) region. This may not be accurate due to early localized deformation that is initiated in the gauge region at elevated temperatures. Treating the post-necking hardening behavior of uniaxial tensile samples has been an important task to expand the effective range of true stress-true strain curves at elevated temperatures for metal and alloys. To explore this issue, uniaxial tensile tests on AA7075-F sheets (with as-fabricated temper) were conducted at 673o K and four different test speeds. The test procedure also utilized an on-line 2-D digital image correlation (DIC) system method to obtain full-field strain map from the deforming gauge region of the test specimen. Local stress-strain curves at different points along the gauge length were then calculated based on the recorded local in-plane principal stress and strain values from macroscopic force data and current cross-section of the specimen at the chosen points. In this manner, the DIC strain analysis not only enabled the determination of stress-strain response but also the determination of strain rates at specific chosen points along the gauge length. The local stress-strain curves revealed significant deviation at an earlier stage of deformation from the global (or macroscopic) stress-strain response based on the entire gauge region. To estimate the constitutive behavior at different strain rates, a correction method to traditional stress-strain curves was applied to obtain a family of stress-strain curves at different constant strain rates based on the local stress-strain curves. Additionally, the material deformation response in the stress, strain and strain rate space in the 3D Cartesian coordinate system was also constructed for tests conducted at different stretching speeds. Further, a verification test was conducted to see if the above methodology could provide an accurate estimation of local deformation behavior of AA7075 sheet. Furthermore, the above experimental method was also coupled with the Gurson-Tvergarrd-Needleman (GTN) ductile void damage model and incorporated into ABAQUS-Explicit general purpose finite element (FE) analysis code via a VUMAT material subroutine. Good agreement was obtained for both the local and global stress-strain curves between the FE test simulation and experimental stress-strain results. The proposed experimental methodology and the resulting stress-strain-strain rate behavior is believed to be applicable in describing the strain rate-dependent constitutive behavior of AA7075-F sheet metals at 673o K.

Characterization on the thermal anisotropic behaviors of high strength AA7075 alloy with the Yld2004-18p yield function

Study on Correlation Between Parameters of "single Factor" Constitutive Model and Temperature for 7050 Aviation Aluminum-Alloy

Hot deformation characteristics and processing maps of AA7075-H18 alloy sheet under hot forming process conditions

Constitutive modelling of plastic deformation behaviour for AA7075-H18 alloy based on hot forming and in-die quenching (HFQ®) process

Analysis of hot Formability of Al-4.6Mg-0.6Mn Alloy (AA5083)

Anisotropic Tensile Behavior and Related Yield Point Phenomena in Annealed Ultrafine-Grained Pure Aluminum

Characterization of the Hot Deformation Behaviour of an As-Extruded Al–Cu–Li Alloy by Constitutive Analysis

Constitutive modeling of deformation in high temperature of a forging 6005A aluminum alloy

A Physical-Based Plane Stress Constitutive Model for High Strength AA7075 under Hot Forming Conditions

Study of Hot Deformation Behavior of 6082 Aluminum Alloy

Modeling the anisotropic plasticity and damage of AA7075 alloy in hot forming

Local and global tensile deformation behavior of AA7075 sheet material at 673oK and different strain rates

Hot tensile deformation behavior and microstructure evolution of 7075 aluminum alloy sheet

Earing Prediction of AA5754-H111 (Al-Alloy) with Linear Transformation-Based Anisotropic Drucker Yield Function under Non-Associated Flow Rule (Non-AFR)

Thermo-mechanical finite element analysis of the AA5086 alloy under warm forming conditions

A new constitutive model and hot processing map of 5A06 aluminum alloy based on high-temperature rheological behavior and higher-order gradients

Constitutive behavior and novel characterization of hot deformation of Al-Zn-Mg-Cu aluminum alloy for lightweight traffic

Hot Working Property Study of 7055 Aluminum Alloy Based on Hot Shear-Compression Deformation

Hot Deformation Behavior of Aluminum Alloys AA7010 and AA7075

Microstructure evolution, constitutive modeling and forming simulation of AA6063 aluminum alloy in hot deformation

Hot Workability of a Spray Formed 2195 Aluminum-Lithium Alloy Based on an Improved Isothermal Processing Map and Drx ‘C-Curve’