Abstract:The 2195 Al-Cu-Li alloy is widely utilized for the fabrication of key aerospace vehicle components; hence, an in-depth understanding of its hot deformation behavior is essential for consistently achieving high-performance products. In this study, isothermal compression tests were performed on 2195 Al-Cu-Li alloy ingots in the temperature and strain rate ranges of 250–500 °C and 10 −3 -1 s −1 , respectively. A processing map was established to predict the workability under different conditions. The corresponding microstructures were examined to reveal their hot deformation mechanism. Results demonstrated that the processing map was divided into four distinct domains. The unstable zone was located in the 250–375 °C/10 −1.5 -1 s −1 and 250–275 °C/10 −2.5 –10 −1.5 s −1 , temperature/strain rate regimes, in which deformation bands and flow localization were observed. The deformation bands blocked dislocations and compromised the dynamic recrystallization (DRX) behavior, hence damaging the microstructure. Further, large coarse T 1 phases precipitated in the 325–410 °C/10 −2.5 –10 −3 s −1 regime, which led to the formation of heterogeneities in the microstructure, corresponding to a minimum workability in the processing map. The optimal hot-working domain for the 2195 alloy was determined to be 460–500 °C/10 −3 –10 −2 s −1 , and the dominating hot deformation mechanisms were DRX and dynamic recovery (DRV). Specifically, continuous and discontinuous DRX behaviors dominated in the 300–400 °C/10 −3 s −1 and 450–500 °C/10 −3 s −1 regimes, respectively. DRX gradually weakened as the strain rate increased at 500 °C. Further, the weakening of DRX was only minimally affected by temperature at 400–500 °C during high-speed deformation (1 s −1 ). The results reported herein can provide valuable insights into the hot working of Al-Cu–Li alloys.

Hot Workability of a Spray Formed 2195 Aluminum-Lithium Alloy Based on an Improved Isothermal Processing Map and Drx ‘C-Curve’

Hot Workability and Dynamic Recrystallization Behavior of a Spray Formed 7055 Aluminum Alloy

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Hot deformation behavior and microstructural evolution of the Al-Cu-Li alloy: A study with processing map

Hot Deformation Behavior and Microstructure Evolution of the Spray Deposited and Secondary Hot Extruded 2195 Al–Li Alloy

Influence of Deformation Parameters on Dynamic Recrystallization of 2195 Al-Li Alloy

Constitutive Analysis and Microstructure Characteristics of As-Homogenized 2198 Al–Li Alloy under Different Hot Compression Deformation Conditions

Hot compressive deformation behavior and microstructural evolution of the spray-formed 1420 Al–Li alloy

The hot deformation characteristics and the associated microstructural evolution of an Al-Cu-Li-Zn alloy studied by constitutive equations and processing maps

Characterization of Hot Deformation Behavior and Processing Maps of Homogenized Al-Mg-Si-Sc-Zr Alloys

Investigation on hot deformation behavior of 2050 Al-Cu-Li alloy

Recrystallization Behavior and Kinetic Analysis of an Al-Cu-Li Alloy During Hot Deformation and Subsequent Heat Treatment

Hot Deformation Behavior and Processing Maps of an As-Cast Al-5Mg-3Zn-1Cu (wt%) Alloy

Hot Deformation Constitutive Model and Processing Maps of Homogenized Al–5Mg–3Zn–1Cu Alloy

Hot deformation characteristics and processing parameter optimization of 2219 Al alloy using constitutive equation and processing map

Hot Deformation Behavior of 2195 Al-Li Alloy Under Plane Strain Compression

T1 precipitate bands and particle stimulated nucleation in 2195 Al-Cu-Li alloy during hot deformation

Hot deformation behavior and microstructure evolution of AA2195 aluminum alloy under cylinder uniaxial compression

Investigation on deformation behaviors and dynamic recrystallization mechanism of spray formed Al–Zn–Mg–Cu alloy under hot compression

Hot Workability Characteristics and Optimization of Processing Parameters of 7475 Aluminum Alloy Using 3D Processing Map

Microstructural Evolution and Dynamic Recrystallization Behavior of the Homogenized 2195 Al–Li Alloy During Hot Deformation