Abstract:Abstract High strength aluminum alloys, especially those that are age-hardenable, such as 2xxx series, 6xxx series, and 7xxx series, are widely used as structural materials in transport and aerospace industries due to their good mechanical properties. However, additive manufacturing of high strength aluminum alloys is challenging due to their susceptibility to hot tearing. In this work, a systematic study has been conducted in an attempt to eliminate hot tearing in laser powder bed fusion (PBF-LB/M) manufacturing of Al2139 alloy through selecting process parameters and the addition of an AlTiB grain refiner. It was found that hot tearing in Al2139 during PBF-LB/M can be reduced or eliminated by increasing volumetric energy density. Furthermore, grain refinement by AlTiB addition shows a clear effect in reducing hot tearing, even though the refined grains remain predominantly columnar rather than equiaxed. The effect of increasing volumetric energy density on hot tearing of Al2139 during PBF-LB/M was analyzed by thermomechanical finite-element simulation, which showed that the reduction in hot tearing with increasing energy density is associated with a decrease in the thermal residual stress. However, it was also shown that there can be a substantive loss of Mg due to evaporation at high energy densities. From a hot tearing model based on solidification thermodynamics, the loss of Mg on hot tearing in Al2139 was estimated to reduce hot tearing by up to 10%, compared to the initial powder composition. With the selected PBF-LB/M parameters, crack-free tensile specimens were fabricated, with and without the addition of AlTiB. Compared with their wrought or cast counterparts, the PBF-LB/M Al2139 and Al2139-AlTiB specimens show lower yield strength but better ductility, which can be attributed to the loss of Mg during PBF-LB/M.

In Fl Uence of Texture and Grain Re Fi Nement on the Mechanical Behavior of AA 2219 Fabricated by High Shear Solid State Material Deposition

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

Effect of Heat Treatment States of Feedstock on the Microstructure and Mechanical Properties of AA2219 Layers Deposited by Additive Friction Stir Deposition

Influence of Grain Refinement and Microstructure on Fatigue Behavior for Solid-State Additively Manufactured Al-Zn-Mg-Cu Alloy

Microstructural and Mechanical Characterization of Additive Friction Stir-Deposition of Aluminum Alloy 5083 Effect of Lubrication on Material Anisotropy

Dynamic Behavior Characterization of Aluminum Alloy 7020 Manufactured Using the Additive Friction Stir Deposition Process

Heterogeneous microstructure development in additive friction-stir deposited Al-Mg-Si alloy

Microstructure and Texture Evolution of Particle-Containing Aa3104 Alloy Cold Rolled to Large Strains

Quantitative study on the correlation between microstructure and mechanical properties of additive friction stir deposited

On the Microstructure, Texture and Electrochemical Properties of Severely deformed and artificially aged Lightweight AA2050 Al-Cu-Li Alloy

Understanding the microstructural evolution and fatigue behavior of aluminum 2319 fabricated by wire arc additive manufacturing

The Effects of Layer Thickness on the Mechanical Properties of Additive Friction Stir Deposition-Fabricated Aluminum Alloy 6061 Parts

Microstructure-deformation relationship of additive friction stir-deposition Al–Mg–Si

Strain Rate Dependent Plasticity Model for Precipitate Hardened Aerospace Aluminum Alloy Produced with Solid-State Additive Manufacturing

Microstructure Evolution and Grain Refinement in 2319 Aluminium Alloy Via Wire Arc Additive Manufacturing Coupled with Multi-Pass Friction Stir Processing

Recrystallization behavior and texture evolution on extrusion connection process of Mg/Al alloys thickness-oriented bonding sheet

Microstructure and Mechanical Behavior Comparison between Cast and Additive Friction Stir-Deposited High-Entropy Alloy Al0.35CoCrFeNi

Effect of process parameters and grain refinement on hot tearing susceptibility of high strength aluminum alloy 2139 in laser powder bed fusion

Effect of Rotational Shear and Heat Input on the Microstructure and Mechanical Properties of Large-Diameter 6061 Aluminium Alloy Additive Friction Stir Deposition

Texture and Mechanical Anisotropy of Ultrafine-Grained Aluminum Alloy AA6016 Produced by Accumulative Roll Bonding

Effect of second-phase precipitates on deformation microstructure in AA2024 (Al–Cu–Mg): dislocation substructures and stored energy