Abstract:Wire arc additive manufacturing (WAAM) technology has potential advantages in the production of large-scale aluminum alloy components. However, as-deposited Al–Cu alloys produced by WAAM often suffer from porosity defects and coarse eutectic phases distributed along the grain boundaries, resulting in poor mechanical properties and hindering the applicability of WAAM to prepare aluminum alloy components. Herein, 2219 aluminum alloy was prepared using WAAM assisted by interlayer friction stir processing (FSP). Porosity defects in the as-deposited materials were eliminated, and coarse eutectic phases were broken and dissolved into the α-Al matrix via interlayer FSP, improving the mechanical properties of the components. The specimens processed by WAAM + interlayer FSP were subjected to different thermal cycling at different locations. The top-layer stir zone (SZ) was not affected by thermal cycling during the additive manufacturing process, and mechanical properties in the SZ were superior to those in the middle region. Compared with the as-deposited materials prepared by WAAM, the yield strength (YS) and ultimate tensile strength (UTS) in the middle region along the horizontal direction of the components manufactured by WAAM + interlayer FSP increased from 118 to 143 MPa and from 255 to 277 MPa, respectively. Further, the ultimate fatigue strength increased from 97 to 139 MPa. The YS and UTS along the vertical direction were 140 and 268 MPa, respectively, which are slightly lower than those along the horizontal direction. This is due to the small overlapping between the two adjacent SZs. The partially melted zone (PMZ) between the SZs was not completely eliminated, and the θ phase in the PMZ was mostly distributed along the grain boundaries.

Microstructure Evolution and Grain Refinement in 2319 Aluminium Alloy Via Wire Arc Additive Manufacturing Coupled with Multi-Pass Friction Stir Processing

Evolution of microstructure and properties in 2219 aluminum alloy produced by wire arc additive manufacturing assisted by interlayer friction stir processing

Microstructure refinement and mechanical properties enhancement of wire-arc additive manufactured 2219 aluminum alloy assisted by interlayer friction stir processing

Enhanced strength-plasticity of 2319 Al-Cu alloy formed by hybrid interlayer friction stir processing and wire-arc additive manufacturing

Microstructure evolution and mechanical properties of wire-arc additive manufactured Al–Zn–Mg–Cu alloy assisted by interlayer friction stir processing

Microstructure refinement and mechanical properties enhancement of wire and arc additively manufactured 6061 aluminum alloy using friction stir processing post-treatment

Improvement of microstructure and fatigue performance of wire-arc additive manufactured 4043 aluminum alloy assisted by interlayer friction stir processing

Gradient microstructure and strength-ductility synergy improvement of 2319 aluminum alloys by hybrid additive manufacturing

Tailoring the microstructure and mechanical properties of wire and arc additive manufactured Al-Mg alloy via interlayer friction stir processing

Microstructural modification and enhanced mechanical properties of wire-arc additive manufactured 6061 aluminum alloy via interlayer friction stir processing

Achieving high performance of wire arc additive manufactured Mg–Y–Nd alloy assisted by interlayer friction stir processing

Microstructural and Defect Evolution during WAAM Resulting in Mechanical Property Differences for AA5356 Component

Enhanced Strength–Ductility Synergy in Submerged Friction Stir Processing ER2319 Alloy Manufactured by Wire-Arc Additive Manufacturing via Creating Ultrafine Microstructure

Improved material properties of wire arc additively manufactured Al-Zn-mg-cu alloy through severe deformation interlayer friction stir processing and post-deposition heat treatment

Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy

Achieving high strength and fatigue performance of wire-arc additive manufactured 6061 aluminum alloy via interlayer friction stir processing and heat treatment

Refined microstructure and enhanced mechanical performance of hybrid additive manufacturing Al-Cu-Mg alloys by multi-cycle friction stirring processing

Achieving high strength-ductility properties of wire-arc additive manufactured Al-Mg-Sc aluminum alloy via friction stir processing post-treatment and high temperature aging treatment

Understanding the microstructural evolution and fatigue behavior of aluminum 2319 fabricated by wire arc additive manufacturing

Enhancing mechanical properties and defects elimination in 2024 aluminum alloy through interlayer friction stir processing in wire arc additive manufacturing

Microstructure and Mechanical Properties of AlSi7Mg0.6 Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)