Abstract:Ultra-high strength 7xxx series aluminum alloys are widely used in aerospace applications due to their exceptional high specific strength. Wire + Arc Additive Manufacturing (WAAM) is a combination of arc and wire feeding additive manufacturing technology including either the gas tungsten arc (GTA) or the gas metal arc (GMA) process. And this technology has been applied in the aerospace manufacturing industry to reduce the time of product development and “buy-to-fly” ratios. However, the existing Al-Zn-Mg-Cu aluminum alloy filler wires are not suitable for WAAM process due to their high susceptibility to hot cracks. In this study, a novel Al-Zn-Mg-Cu-Sc aluminum alloy wire named 7A55-Sc with ultra-high strength and excellent hot-crack resistance has been successfully prepared by optimizing the composition of Al-Zn-Mg-Cu alloying elements and adding appropriate amounts of inoculants Sc and Zr elements during the smelting process. And then, thin-wall components without any hot cracks were successfully fabricated by using cold metal transfer (CMT) process. Results indicated that the microstructure of the as-deposited 7A55-Sc alloy consists of predominantly fine equiaxed grains and the average size of the grains is between 5.0 and 6.0 μm. The eutectics composed of α (Al), η phase and S phase were distributed along the grain boundaries. The Al3Sc and Al3 (Zr, Sc) particles precipitated within grains act as heterogeneous nucleation nuclei, promoting the formation of the equiaxed grains. After T6 heat treatment, most of the second phases distributed within grains and grain boundaries were dissolved into the α(Al) matrix. The distribution of alloy elements became more homogeneous. The average ultimate tensile strength, yield strength and elongation of T6 heat-treated 7A55-Sc alloy in the horizontal direction were 554 MPa, 488 MPa and 1.7% respectively, whereas 523 MPa, 469 MPa and 1.4% in the vertical direction. The lower ductility was considered due to the existence of a large number of pores in the 7A55-Sc alloy fabricated by the CMT process.

Achieving high strength-ductility properties of wire-arc additive manufactured Al-Mg-Sc aluminum alloy via friction stir processing post-treatment and high temperature aging treatment

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Microstructure refinement and mechanical properties enhancement of wire and arc additively manufactured 6061 aluminum alloy using friction stir processing post-treatment

Achieving high strength and fatigue performance of wire-arc additive manufactured 6061 aluminum alloy via interlayer friction stir processing and heat treatment

Improved material properties of wire arc additively manufactured Al-Zn-mg-cu alloy through severe deformation interlayer friction stir processing and post-deposition heat treatment

Microstructure refinement and mechanical properties enhancement of wire-arc additive manufactured 2219 aluminum alloy assisted by interlayer friction stir processing

Improvement of microstructure and fatigue performance of wire-arc additive manufactured 4043 aluminum alloy assisted by interlayer friction stir processing

Microstructural modification and enhanced mechanical properties of wire-arc additive manufactured 6061 aluminum alloy via interlayer friction stir processing

Tailoring the microstructure and mechanical properties of wire and arc additive manufactured Al-Mg alloy via interlayer friction stir processing

Microstructure evolution and mechanical properties of wire-arc additive manufactured Al–Zn–Mg–Cu alloy assisted by interlayer friction stir processing

Microstructure tuning enables synergistic improvements in strength and ductility of wire-arc additive manufactured commercial Al-Zn-Mg-Cu alloys

Achieving high strength-ductility of Al-Zn-Mg-Cu alloys via hot-wire arc additive manufacturing enabled by strengthening precipitates

Evolution of microstructure and properties in 2219 aluminum alloy produced by wire arc additive manufacturing assisted by interlayer friction stir processing

Microstructure and mechanical properties of 600 MPa grade ultra-high strength aluminum alloy fabricated by wire-arc additive manufacturing

Mechanical properties and precipitation behavior of the heat-treated wire + arc additively manufactured 2219 aluminum alloy

Microstructure and Mechanical Properties of AlSi7Mg0.6 Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)

Microstructure Evolution and Grain Refinement in 2319 Aluminium Alloy Via Wire Arc Additive Manufacturing Coupled with Multi-Pass Friction Stir Processing

Enhanced strength-plasticity of 2319 Al-Cu alloy formed by hybrid interlayer friction stir processing and wire-arc additive manufacturing

Microstructure and mechanical properties of ultra-high strength Al-Zn-Mg-Cu-Sc aluminum alloy fabricated by wire + arc additive manufacturing

Minimizing porosity and optimizing microstructure of hot-wire arc additive manufactured Al-Cu-Mg-Ag alloy for strength increment

Microstructure and mechanical properties of wire arc additively manufactured 205A high strength aluminum alloy: The comparison of as-deposited and T6 heat-treated samples